Pelican Parts Forums

Pelican Parts Forums (
-   Canada (
-   -   FS 1980 930 Turbo Project Car (

Jim2 09-28-2008 08:53 AM

FS 1980 930 Turbo Project Car
My 930 project was abandoned in lieu of a different project. After advertising for a while I received no interest in the whole car so instead I decided to part it out. Thanks to this Canadian forum it resulted in the sale of everything (the entire car!) except the few items noted below. Most of the parts stayed local and only a couple items needing shipping. Thanks to all.

For any remaining items I'd prefer to ship within Canada to avoid border issues. The 911 parts were other odds and ends sitting in my garage.

Graphite black 930 rear bumper with fender extensions $400

Sun visors $50

Early sport muffler from a 911. It was modded for pea shooters but they were removed. 60mm tail pipe. Very good cond. Only used for 16K kms $150

Pair of heat boxes, one rusty, the other good. free - local pick up

Pair of bare boge strut housings. Spindles are functional but not the best cond. $200

930/911 Adjustable ride height spring plates $125

930 tach and spedo are sold. The oil press/temp and fuel/oil level remain $50

Front aluminum crossmember $100

Oil lines -repaired but decent cond. $300

Items sold:
chassis, doors, fenders
fuel pump
oil cooler
pedal box
fuel tank
parking brake parts
glass and moldings
Trans x member
Shifter assembly
Seat belts
Trailing arms

wideRSR 10-08-2008 08:24 PM

hey Jim I gave you beer for tail lights... do you still have some of those turbo parts availiable... I'm thinking about the intercooler you had... would that fit under a duck tail?

wideRSR 11-28-2008 02:05 PM


this was on Kijiji they are looking for a turbo.. might want to check them out.

Jim2 12-01-2008 07:31 PM

Pair of new a/c fittings, voltage regulator, new rear seat clip, Momo steering wheel horn pad cover, Momo gas pedal, pair of aftermarket fogs - one lens missing, Center console (not pictured) Wastegate pipe and air duct are sold. All/ Case of really cheap beer

911 Harness bar $125

930 intercooler shroud $100

A/C pump (has one broken ear) and 930 wing condensor $100

930 9 bolt 245mm flywheel, stock rubber centerd disk and pressure plate, and release bearing $200

930 Turbo tail in very good condition $800

Oracle 12-02-2008 08:28 PM

Please let me know your paypal account.


MARTIN AIDE 12-05-2008 04:26 PM

Hi Jim,do you still have the fenders and rear flares?Marty

Jim2 12-05-2008 05:44 PM

Hi Marty, rear quarters and fenders are taken.

930 rear seats from a mid 90s turbo, leather, carpet on rear of one is missing $50

Oracle 12-07-2008 09:10 PM

I just sent you the money as per our conversation


Won 12-10-2008 12:26 AM

Do you think the rear and quarter glasses can be shipped safely to Vancouver? Would you sell only the window frames and glasses separate from the doors?

Browzer52 12-21-2008 08:02 PM

Would like the old oil line,but just 6" of each end if you would cut and mail to Campbell River BC.Adapting a second oil cooler to my 930,need the ends to weld jic adaptors to.Postal code is V9H 1J2,please advise on cost shipped in CDN dollars.Thanks

Jim2 12-21-2008 08:18 PM

$25 OK? This will cover postage and leave two bits for my time to post, oh ya, it'll cover my six pack too!

I'll PM my paypal id. Please reply back with your full address etc for the package. I'd like to wait until next week after the Christmas rush dies off at the post offices.

Need an extra fender oil cooler? I have one.

Browzer52 12-22-2008 08:20 PM

PM sent

Dai 12-25-2008 10:08 AM

Jim, I'm interested the under dash cover which hides wiring and heater hoses on 911s, made by Moch-1, $75 and I live in Calgary. Please send me pm to arrange for transaction. Thanks.

unclebilly 01-04-2009 08:03 AM


if the shifter is still available, give me a call.

Now i have to go outside and move snow... story of my life these days.


Jim2 01-04-2009 08:19 AM

Sent you a PM Scott.

unclebilly 01-04-2009 04:36 PM


my pm box was full. try again.

timbieber 02-10-2009 08:35 PM

did u sell the wheels?

timbieber 02-11-2009 08:00 AM

Are you flexible on price? I'm in Vancouver so easy and we can exchange in CDN$'s
So these are early off-set 23mm front and rear?
fire me an email to

Jim2 02-11-2009 08:10 AM

The offsets are at the very top of my first post 23mm front and 15mm rear. $700 firm

How to ship?

California#1 02-13-2009 10:32 AM

Hi Jim,

Do you still have the muffler and will it work on an unblown 3.2 1985 car. Would you also happen to know where I can source parts here in Canada....

Kind regards,


All times are GMT -8. The time now is 04:14 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2020 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.