Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Technical BBS > 4- Classified Ads > Porsche 911 Used Parts For Sale & Wanted

Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered User
 
Join Date: Jun 2008
Posts: 156
Torsion Bars- Hollow 32mm and 24.6mm

Front bars measure 24.65mm OD and 13mm ID SOLD SOLD
Rear bars measure 32mm OD and 18.8mm ID.
Equivalent solid bar sizes would be 24 and 31mm.
These are for the PRE G50 cars
No corrosion or damage. ready to go.

$185 per pair plus shipping from 97009. shipping weights are approx. 9 and 13 lbs.

Last edited by Donnsny; 11-14-2017 at 06:08 PM..
Old 11-08-2017, 01:39 PM
  Pelican Parts Technical Article Directory    Reply With Quote #1 (permalink)
Registered User
 
jamesjedi's Avatar
 
Join Date: Aug 2004
Location: The Brink
Posts: 2,059
Confirming the effective rate for the front bars is 24 mm?

Are they marked left and right?

Are the fronts Sanders?
Old 11-08-2017, 03:48 PM
  Pelican Parts Technical Article Directory    Reply With Quote #2 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
The fronts are stamped with a se. I am assuming sanders engineering. There is no right or left stamp or mark. You can however see which way they went by the dryed grease/dirt on one side of the splines. The loaded sides of the teeth are much cleaner.
The rears are marked L and R.
Thanks, Donn
Old 11-08-2017, 06:26 PM
  Pelican Parts Technical Article Directory    Reply With Quote #3 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
Yes the effective rate of the fronts would be 24mm. Or close to it. I will run the numbers and post later. Dinner is ready.
Thanks, Donn
Old 11-08-2017, 06:31 PM
  Pelican Parts Technical Article Directory    Reply With Quote #4 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
According to dimensions listed above the front bars are equivalent to a 24.2 mm solid bar. This gives a wheel rate of 260 lbs/in. with stock 911 geometry.
Donn
Old 11-08-2017, 07:36 PM
  Pelican Parts Technical Article Directory    Reply With Quote #5 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
The rear bars are in fact very close to 31 mm solid equivalent which gives 351 lbs/inch wheel rate with stock rear geometry.
Old 11-08-2017, 07:44 PM
  Pelican Parts Technical Article Directory    Reply With Quote #6 (permalink)
Registered User
 
jamesjedi's Avatar
 
Join Date: Aug 2004
Location: The Brink
Posts: 2,059
I think that the effective rate numbers are usually stamped.
Old 11-09-2017, 06:23 AM
  Pelican Parts Technical Article Directory    Reply With Quote #7 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
stamps on ends of bars

Here are some pictures of the stamps on the ends of the bars.
Old 11-09-2017, 01:35 PM
  Pelican Parts Technical Article Directory    Reply With Quote #8 (permalink)
Registered User
 
jamesjedi's Avatar
 
Join Date: Aug 2004
Location: The Brink
Posts: 2,059
I am interested in the 24's. Can you provide a picture of the splines? Thanks.

Last edited by jamesjedi; 11-10-2017 at 01:59 PM..
Old 11-09-2017, 03:10 PM
  Pelican Parts Technical Article Directory    Reply With Quote #9 (permalink)
Registered User
 
jamesjedi's Avatar
 
Join Date: Aug 2004
Location: The Brink
Posts: 2,059
pm sent
Old 11-10-2017, 01:58 PM
  Pelican Parts Technical Article Directory    Reply With Quote #10 (permalink)
Registered User
 
jamesjedi's Avatar
 
Join Date: Aug 2004
Location: The Brink
Posts: 2,059
I will take the 24mm SE bars if the splines are good.
Old 11-11-2017, 08:05 PM
  Pelican Parts Technical Article Directory    Reply With Quote #11 (permalink)
Registered User
 
Join Date: Jun 2008
Posts: 156
The front bars are sold. Thank you.
Rear bars still available
Old 11-14-2017, 06:08 PM
  Pelican Parts Technical Article Directory    Reply With Quote #12 (permalink)
 
Now Available for Ordering:   101 Projects For Your BMW 3 Series 1982-2000  [more info]
Registered User
 
Join Date: Jun 2008
Posts: 156
The rear bars are still available. Thanks
Old 11-18-2017, 07:10 PM
  Pelican Parts Technical Article Directory    Reply With Quote #13 (permalink)
Reply

Thread Tools
Rate This Thread
Rate This Thread:

 


All times are GMT -8. The time now is 11:23 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2016 Pelican Parts - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.