Pelican Parts Forums

Pelican Parts Forums (http://forums.pelicanparts.com/)
-   Porsche 914 & 914-6 Technical Forum (http://forums.pelicanparts.com/porsche-914-914-6-technical-forum/)
-   -   Conversion from 914-6 (http://forums.pelicanparts.com/porsche-914-914-6-technical-forum/580946-conversion-914-6-a.html)

HKZ Bob 12-18-2010 02:30 AM

Conversion from 914-6
 
Dear Forum,

I am working on a project to integrate a 6 cylinder into a 914-4 harness.

I am looking for Photos of the original 914-6.

Specially:

Where was the CDI positioned?
Where was the alternator regulator was positioned?

Who has diagramm of the 914-4 Control Board.
I am interesting in the physical pin output and like to match it with the 911 engine harness.

I would like to use the experience on existing knowlage and not go though all problems too.

Regards
Merry Chistmas 2010

HKZ Bob 12-18-2010 03:13 AM

http://forums.pelicanparts.com/uploa...1292670812.jpg

HKZ Bob 12-18-2010 03:23 AM

I am getting closer,

Who did this conversion already.
I the schematic correct? I guess not.
I need the connector endview of an 1971 911 2.2 engine




http://forums.pelicanparts.com/uploa...1292671380.jpg

larrym 01-02-2011 10:07 PM

best thing you can do for yourself is to is buy Art zapf's 914-6 color wiring diagram

http://forums.pelicanparts.com/porsche-914-914-6-technical-forum/78526-search-over-914-6-wiring-diagram.html

or for $10, I will sell you Art's earlier b/w 2-part diagram with color codes listed

one caveat - I have found that the wire colors on various years & models is not consistent, so expect to do some end-to-end tracing no matter what diagrams you capture

Cairo94507 01-03-2011 06:26 AM

I do not believe Art's color schematics are available any more. I tried several times to buy one from him and never was able. I think Art just stopped making them. If he ever did another run I would buy one for my garage wall.

I ultimately bought one from Jeff Bowlesby and have that one which I consider priceless.

HKZ Bob 01-03-2011 08:22 AM

Hi Happy new year, 2011

my intent of this thread was more to see how other people placed the CDI and
what is tricky on the conversion

Photos will be good of original 914-6

Please share date.
I have the schematic already which I need.

BRhttp://forums.pelicanparts.com/uploa...1294071751.jpg

Jared at Pelican Parts 01-03-2011 10:51 AM

http://forums.pelicanparts.com/uploa...1294080686.jpg

this may help

HKZ Bob 01-03-2011 12:03 PM

Jared thank you,

Can you dive with your camera in the engine compartment and picture

the electric board, fuel pump, you are using a permature, and everything what need to be seen.

BR
Bob

Geil

larrym 01-03-2011 12:38 PM

Art is producing the diagram again - one sheet, all color - Zapf Enterprises

racer 01-03-2011 01:27 PM

jared.. where's your battery ;) doh!

quicksix 01-03-2011 01:39 PM

Hey Bob,
try over on the 914 world board,in the originality section.
Lots of stock/factory engine bays
John


All times are GMT -8. The time now is 04:45 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website


DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.