Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums
Reload this Page Search Results
Register Garage FAQ Community Calendar Today's Posts Search


Showing results 1 to 13 of 13
Search took 0.01 seconds. Search: Posts Made By: VB_Racing
Forum: Porsche 924/944/968 Technical Forum 09-20-2010, 05:44 PM
Replies: 16
Views: 3,048
Posted By VB_Racing
I will get some service info tomorrow at work,...

I will get some service info tomorrow at work, and will be able to tell you what else could be in the circuit. If the DME relay is good and your grounds are good, you should be ok. If you have a dvom...
Forum: Porsche 924/944/968 Technical Forum 09-19-2010, 04:47 PM
Replies: 16
Views: 3,048
Posted By VB_Racing
Yes it matters, you want the wire that gets...

Yes it matters, you want the wire that gets constant 12v. should be a fused circuit independant of the DME.
Forum: Porsche 924/944/968 Technical Forum 09-19-2010, 04:45 PM
Replies: 16
Views: 3,048
Posted By VB_Racing
Joe, a noid light does NOT check injectors, it...

Joe, a noid light does NOT check injectors, it tells you if you have a good signal to the injectors. Having 12 volts at both sides of the injector tells you nothing about the DME because you don't...
Forum: Porsche 924/944/968 Technical Forum 09-19-2010, 05:16 AM
Replies: 16
Views: 3,048
Posted By VB_Racing
Did you use a noid light at the injector...

Did you use a noid light at the injector connector? If you get a consistent bright light at the injector you have good signal, but anything else you don't. You say you have varying voltages at the...
Forum: Porsche 924/944/968 Technical Forum 08-02-2010, 06:56 PM
Replies: 43
Views: 9,878
Posted By VB_Racing
I see... That's a great way to do it, the...

I see... That's a great way to do it, the capacitors will depower, and the unit will only have ground if you do it that way, you are essentially taking away the power source for igniting the bags,...
Forum: Porsche 924/944/968 Technical Forum 08-02-2010, 12:42 PM
Replies: 43
Views: 9,878
Posted By VB_Racing
Looks great. you did your homework!! Just a...

Looks great. you did your homework!! Just a little advice on the disabled portion of the airbags, most manufacturers have a shorting bar that shorts the terminals of the bags when disconnected. If...
Forum: Porsche 924/944/968 Technical Forum 06-13-2010, 05:50 PM
Replies: 43
Views: 9,878
Posted By VB_Racing
I have seen 2 BMW's in the past blow airbags off...

I have seen 2 BMW's in the past blow airbags off when bounding curbs at Blackhawk Farms either on track days or Autox. I would bet that you set off at least one impact sensor, and the safing sensor...
Forum: Porsche 924/944/968 Technical Forum 06-13-2010, 02:34 PM
Replies: 12
Views: 486
Posted By VB_Racing
You have to remember that oil temp is going to be...

You have to remember that oil temp is going to be a bit higher than water temp usually, so if you are running 210 to 220 water temp, then you could easily have oil temp of 270, that will cause a drop...
Forum: Porsche 924/944/968 Technical Forum 06-13-2010, 12:49 PM
Replies: 12
Views: 486
Posted By VB_Racing
So yesterday you had the same oil pressure at...

So yesterday you had the same oil pressure at speed and at idle when hot? Any unusual noise? Where was you water temp?
Forum: Porsche 924/944/968 Technical Forum 06-13-2010, 12:28 PM
Replies: 12
Views: 486
Posted By VB_Racing
Are you looking at your factory gauge, or do you...

Are you looking at your factory gauge, or do you have an aftermarket gauge installed. 3 bar is still 42 psi of oil pressure( not really an issue), so it may be a case of just heat, it would help if...
Forum: Porsche 924/944/968 Technical Forum 06-13-2010, 10:45 AM
Replies: 17
Views: 2,569
Posted By VB_Racing
Not to hijack the thread, but no, not really. I...

Not to hijack the thread, but no, not really. I have been involved in engine building for quite awhile, I am a Ford senior master tech, and have worked as a technical consultant with quite a few...
Forum: Porsche 924/944/968 Technical Forum 06-12-2010, 05:52 PM
Replies: 17
Views: 2,569
Posted By VB_Racing
The stud is steel. The reference sensor is...

The stud is steel. The reference sensor is magnetic. The sensor produces voltage, when the stud passes it. If you watch the signal coming off the reference sensor on an Oscope it will produce AC...
Forum: Porsche 924/944/968 Technical Forum 05-30-2010, 04:26 AM
Replies: 34
Views: 2,793
Posted By VB_Racing
Wow, glad to hear you are OK, very fast part of...

Wow, glad to hear you are OK, very fast part of the track to have an off, as you know Im sure.I'm from WI also, if you need a hand with anything dont be afraid to let me know.
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -8. The time now is 12:20 AM.

Contact Us - Pelican Parts Catalog for Porsche, BMW, Mercedes-Benz, MINI and More - Archive - Privacy Statement - Terms of Service - Top

 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.