Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums


Showing results 1 to 25 of 452
Search took 0.05 seconds.
Search: Posts Made By: racing97
Forum: 911 Engine Rebuilding Forum Yesterday, 07:42 AM
Replies: 3
Views: 129
Posted By racing97
Look at the path of the individual oil path...

Look at the path of the individual oil path through the crank specifically on the journal in question. They are adjacent to the crank pin in the center they are on both sides.
Those passage ways...
Forum: 911 Engine Rebuilding Forum 12-21-2018, 12:16 PM
Replies: 28
Views: 1,369
Posted By racing97
You should check with EBS and have them contact...

You should check with EBS and have them contact the machine shop for what they torqued them to. I could vary and I doubt the machine shop used torque angle.
Anyway if that is not forcomming put you...
Forum: 911 Engine Rebuilding Forum 12-18-2018, 02:09 PM
Replies: 28
Views: 1,369
Posted By racing97
Yes an ARP stretch gauge or something similar and...

Yes an ARP stretch gauge or something similar and a Snapon torque link extension with a 3/8 square provision on one end and on the other a 7/16 or 11mm depending on what size the rod fastener is and...
Forum: Off Topic Discussions 12-18-2018, 09:17 AM
Replies: 22
Views: 762
Posted By racing97
Damn that was good!

Damn that was good!
Forum: 911 Engine Rebuilding Forum 12-10-2018, 06:41 PM
Replies: 37
Views: 1,467
Posted By racing97
Gordon you did the right thing talking to John

Gordon you did the right thing talking to John
Forum: Porsche 911 Technical Forum 12-10-2018, 03:05 PM
Replies: 24
Views: 1,979
Posted By racing97
Man I admire folks that do these very difficult...

Man I admire folks that do these very difficult projects, but I can't tell you the many times Porsche has all of a sudden released the very product that they have recreated. I sure hope this is not...
Forum: 911 Engine Rebuilding Forum 12-07-2018, 04:15 PM
Replies: 37
Views: 1,467
Posted By racing97
Now that you have the parameters of installed...

Now that you have the parameters of installed height and load you may want to take note of how much lift your spring will tolerate before solid height comes into play.

regards
Forum: 911 Engine Rebuilding Forum 11-29-2018, 07:47 PM
Replies: 37
Views: 1,467
Posted By racing97
You probably should measure the stock spring...

You probably should measure the stock spring although the spring rate may be close to 290 as I recall they have now where near a seat pressure of 130 and do not produce more than 230 full open.
Just...
Forum: 911 Engine Rebuilding Forum 11-21-2018, 06:39 PM
Replies: 17
Views: 859
Posted By racing97
Jeff Erickson the "Jefe"

Jeff Erickson the "Jefe"
Forum: Porsche 911 Technical Forum 11-13-2018, 07:07 PM
Replies: 13
Views: 645
Posted By racing97
If it is the very first oil change consider that...

If it is the very first oil change consider that ome people use mysterious engine assembly lubes that may contain some of the above concerns.
Get the engine warm and change the oil and do the sample...
Forum: 911 Engine Rebuilding Forum 11-12-2018, 07:03 PM
Replies: 2
Views: 173
Posted By racing97
I think if you ordered a camshaft on a new cam...

I think if you ordered a camshaft on a new cam core the only ones currently available are the later design. So you will need the bolts and washers and you will have to order them from the Porsche...
Forum: Porsche 911 Technical Forum 11-09-2018, 09:26 AM
Replies: 6
Views: 299
Posted By racing97
Just from what you can see it looks like a cast...

Just from what you can see it looks like a cast 2.2 911 T
Forum: 911 Engine Rebuilding Forum 10-13-2018, 10:27 AM
Replies: 2
Views: 355
Posted By racing97
Yeah that is too much interference .0015 is all...

Yeah that is too much interference .0015 is all you want, if it has gone in crooked due to the interference and effort to put it in you are in a bit of trouble cutting the seat and it will just make...
Forum: 911 Engine Rebuilding Forum 10-12-2018, 07:44 AM
Replies: 43
Views: 3,580
Posted By racing97
Quite contrary they are good sorry I was not as...

Quite contrary they are good sorry I was not as adamit as my previous post...
Forum: 911 Engine Rebuilding Forum 10-11-2018, 07:51 PM
Replies: 43
Views: 3,580
Posted By racing97
I have searched this thread for some substance...

I have searched this thread for some substance but have found none until I came across your post you remind me of my friend Herman from S.A. he is quite bright also.
Oddly enough Porsche and I...
Forum: 911 Engine Rebuilding Forum 10-06-2018, 07:00 PM
Replies: 43
Views: 3,580
Posted By racing97
Neil it is great that you have entered the fray I...

Neil it is great that you have entered the fray I am sure you will not suffer from instrumentation for data collection and that you would not be just re branding others products, what are you using...
Forum: 911 Engine Rebuilding Forum 09-26-2018, 07:46 PM
Replies: 9
Views: 494
Posted By racing97
Well you can see how the Piston on the left has...

Well you can see how the Piston on the left has been reworked it has milling marks in the pocket and lathe marks on the deck. Mahle makes a lot of Pistons and they have far superior material...
Forum: 911 Engine Rebuilding Forum 09-13-2018, 09:37 AM
Replies: 21
Views: 1,127
Posted By racing97
9000 rpm is attainable but the increases in ...

9000 rpm is attainable but the increases in power will be the hard part, you would have to figure 8500 power peak with and extra 500 to be well in the curve only the 4v RSR's have achieved it and...
Forum: 911 Engine Rebuilding Forum 08-16-2018, 03:27 PM
Replies: 8
Views: 406
Posted By racing97
More snap more power and higher thermal...

More snap more power and higher thermal efficiency.
Gains all across the range some of the power goes to driving the rings into the bore a little harder so it is more noticable going from the 8's...
Forum: 911 Engine Rebuilding Forum 08-16-2018, 08:24 AM
Replies: 8
Views: 406
Posted By racing97
This is correct just look at the difference in...

This is correct just look at the difference in the domes of the two pictures.
This has been going on for years and years those that do know how to check compression generally have better power than...
Forum: 911 Engine Rebuilding Forum 08-14-2018, 08:05 PM
Replies: 20
Views: 860
Posted By racing97
I would be interested in any situation where...

I would be interested in any situation where someone has offset the inlet port, lets see 15 to 20 degrees or so. As of yet I have seen probably the best use of straight up cross flow, and that is...
Forum: 911 Engine Rebuilding Forum 06-25-2018, 07:45 AM
Replies: 153
Views: 14,327
Posted By racing97
I have to say the heat effect on the diffuser is...

I have to say the heat effect on the diffuser is brilliant!
Forum: 911 Engine Rebuilding Forum 06-12-2018, 07:39 PM
Replies: 5
Views: 410
Posted By racing97
10:1

10:1
Forum: 911 Engine Rebuilding Forum 06-06-2018, 08:04 PM
Replies: 8
Views: 622
Posted By racing97
porque?

porque?
Forum: Porsche 911 Technical Forum 06-01-2018, 07:27 PM
Replies: 15
Views: 858
Posted By racing97
Not from Asia forgings come from Michigan.

Not from Asia forgings come from Michigan.
Showing results 1 to 25 of 452

 
Forum Jump

All times are GMT -8. The time now is 12:40 AM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.