Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums


Showing results 1 to 25 of 218
Search took 0.04 seconds.
Search: Posts Made By: The Turk
Forum: Porsche 911 Technical Forum 11-13-2018, 12:04 PM
Replies: 14
Views: 789
Posted By The Turk
Hi Greg, I was trying to find a 1982-1985...

Hi Greg, I was trying to find a 1982-1985 Excellence magazine with a small advertisement in the back for ”Troutman” aluminum slopenose fenders with 928 headlights.
I had these fenders installed back...
Forum: Porsche 911 Technical Forum 01-29-2009, 02:41 PM
Replies: 6
Views: 812
Posted By The Turk
I had the same problem when I installed the...

I had the same problem when I installed the Motronic DME for my conversion, it turned out I had hooked up the black wire off the Motronic wiring harness to a fuse that lost power when the key was...
Forum: 911 / 930 Turbo & Super Charging Forum 07-22-2008, 08:34 AM
Replies: 4
Views: 577
Posted By The Turk
Just because you didn't set them to 20 degrees...

Just because you didn't set them to 20 degrees doesn't mean they're not at 20 degrees, they don't always rotate out of adjustment.
If they are off, the car will pull to one side and/or one or more...
Forum: Porsche 911 Technical Forum 07-22-2008, 08:24 AM
Replies: 7
Views: 725
Posted By The Turk
I'm pretty sure electronic speedo's started in...

I'm pretty sure electronic speedo's started in 76, that appears to be an early (pre 85) electronic speedo sending unit, maybe the car had a later motor and tranny installed at some point in the past.
Forum: Porsche 911 Technical Forum 06-13-2008, 10:42 AM
Replies: 10
Views: 638
Posted By The Turk
Hi Mark, I run an LM1 and AuxBox in my car, I...

Hi Mark,
I run an LM1 and AuxBox in my car, I log RPM, Speed, AFR, throttle position and boost from two different locations.
Setting the LM1 / AuxBox up can be challenging but is worth it once your...
Forum: Porsche 911 Technical Forum 06-09-2008, 04:03 PM
Replies: 3
Views: 408
Posted By The Turk
Unfortunately it doesn't take much to plug one of...

Unfortunately it doesn't take much to plug one of the holes, some particles may have got into the bar while the cam tower was in the cleaning tank when you had your heads done.

I had the machine...
Forum: Porsche 911 Technical Forum 06-09-2008, 11:21 AM
Replies: 3
Views: 408
Posted By The Turk
If it's the same valve getting loose each time...

If it's the same valve getting loose each time you probably have a clogged oil spray bar and one or more of the rockers and cam lobes aren't getting any oil.
I had the same problem and roasted a...
Forum: 911 / 930 Turbo & Super Charging Forum 05-19-2008, 02:00 PM
Replies: 16
Views: 1,676
Posted By The Turk
I was really concerned about fire also, I just...

I was really concerned about fire also, I just installed a Safecraft 10lb. Halon, one nozzle in the passenger compartment and two in the motor, one on each side.
I ran aluminum hard lines inside the...
Forum: 911 / 930 Turbo & Super Charging Forum 05-15-2008, 03:43 PM
Replies: 8
Views: 690
Posted By The Turk
My car came with that same Ungo Box, you armed it...

My car came with that same Ungo Box, you armed it by pushing the button, when you re-entered the car you had 20 seconds to dial in the correct code and push the button, if you used the wrong code it...
Forum: Porsche 911 Technical Forum 05-08-2008, 03:47 PM
Replies: 11
Views: 567
Posted By The Turk
If you put the car in 1st with the clutch in at a...

If you put the car in 1st with the clutch in at a standing stop and start the motor does the car want to move forward ?
Forum: Porsche 911 Technical Forum 05-08-2008, 03:24 PM
Replies: 11
Views: 567
Posted By The Turk
Is there a lot of pedal free play ? With the...

Is there a lot of pedal free play ?
With the motor running does everything sound ok when the pedal is pushed in ?
Forum: Porsche 911 Technical Forum 04-03-2008, 10:47 PM
Replies: 1
Views: 281
Posted By The Turk
It's not going to make a difference.

It's not going to make a difference.
Forum: 911 / 930 Turbo & Super Charging Forum 03-18-2008, 10:17 PM
Replies: 36
Views: 3,036
Posted By The Turk
I think the clips you’re wondering about hold the...

I think the clips you’re wondering about hold the pressure plate in a little bit for installation, here’s a picture of a new early 935 pressure plate with the clips I installed as part of a shortened...
Forum: Porsche 911 Technical Forum 03-12-2008, 12:02 PM
Replies: 3
Views: 585
Posted By The Turk
Hi Bill, Thanks for chiming in. I’m not...

Hi Bill,
Thanks for chiming in.
I’m not familiar with Prosystem, are you talking about Pro-System in Mooresville, NC ?

Are you suggesting I might want to look at non-floating because the cost of...
Forum: Porsche 911 Technical Forum 03-12-2008, 09:34 AM
Replies: 3
Views: 585
Posted By The Turk
Front Floating Rotors

Awhile back I installed front and rear 993 calipers with rear factory Turbo rotors and 993 front rotors on turned down hubs.

I have some new hubs and decided to upgrade the fronts to the 1978-80...
Forum: Porsche 911 Technical Forum 03-11-2008, 12:26 PM
Replies: 65
Views: 22,819
Posted By The Turk
Hi 1topcat, I moved the entire parking brake /...

Hi 1topcat,
I moved the entire parking brake / manual heater control assembly to the original location of the stock shifter, check out the picture on page 1 of this thread.
The small notch in the...
Forum: Porsche 911 Used Parts For Sale & Wanted 03-11-2008, 11:36 AM
Replies: 48
Views: 3,758
Posted By The Turk
Hi Dave, Do you still have the front hubs ? ...

Hi Dave,
Do you still have the front hubs ?
If so, how much do you want for them shipped to California ?
Forum: Porsche 911 Technical Forum 03-05-2008, 10:56 AM
Replies: 27
Views: 2,255
Posted By The Turk
Hi Kevin, If you have 100 PSI oil pressure when...

Hi Kevin,
If you have 100 PSI oil pressure when the motor is warmed up to running temps there is definitely something not working correctly with the pressure relief pistons.
You should remove them...
Forum: Porsche 911 Technical Forum 02-15-2008, 09:33 AM
Replies: 35
Views: 2,796
Posted By The Turk
Assembled crank. ...

Assembled crank.
http://forums.pelicanparts.com/uploads12/IMG_88211203096685.jpg

3.5 going together with GT3R oil pump.
http://forums.pelicanparts.com/uploads12/IMG_91771203096462.jpg
Forum: Porsche 911 Technical Forum 02-04-2008, 12:28 PM
Replies: 8
Views: 641
Posted By The Turk
Yes it mounts in the hole in front of the gear...

Yes it mounts in the hole in front of the gear shift, the bolts come through the bottom of the car to hold it in place, I lengthened the hole by about 2" to make installation easier.
A buddy of mine...
Forum: Porsche 911 Technical Forum 02-04-2008, 10:39 AM
Replies: 8
Views: 641
Posted By The Turk
Hi Steve, When I did my G50 conversion, I...

Hi Steve,

When I did my G50 conversion, I made up a bracket that holds the clutch master cylinder and installs into the tunnel, I used the original pedal cluster, no modification is necessary to...
Forum: 911 / 930 Turbo & Super Charging Forum 02-01-2008, 01:04 PM
Replies: 33
Views: 1,969
Posted By The Turk
Take this advice with a grain of salt.... I'm...

Take this advice with a grain of salt....
I'm your basic bench racer home hobbyist welder, I have a Lincoln 175 which is similar to yours.
You should treat yourself to a small tank of 75% Argon 25%...
Forum: Porsche 911 Technical Forum 01-22-2008, 11:50 AM
Replies: 6
Views: 1,421
Posted By The Turk
Hi John, After talking with a few highly...

Hi John,
After talking with a few highly regarded engine builders, I chose the GT3 oil pump when I was building my twin turbo 3.5, it has the same pressure side as the turbo pump but a larger...
Forum: Porsche 911 Technical Forum 01-20-2008, 11:26 AM
Replies: 376
Views: 107,417
Posted By The Turk
Here's mine, 2 in 2 out Protomotive muffler. ...

Here's mine, 2 in 2 out Protomotive muffler.

<object width="425" height="355"><param name="movie" value="http://www.youtube.com/v/L0F6cV95jfI&rel=1"></param><param name="wmode"...
Forum: Porsche 911 Technical Forum 01-17-2008, 04:49 PM
Replies: 376
Views: 107,417
Posted By The Turk
kcpaz, Which Magnaflow are you using ? Your car...

kcpaz,
Which Magnaflow are you using ? Your car sounds great, not too loud.
Any pictures of the muffler installed on the car ?
Showing results 1 to 25 of 218

 
Forum Jump

All times are GMT -8. The time now is 04:15 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2020 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.