Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums


Showing results 1 to 25 of 500
Search took 0.13 seconds.
Search: Posts Made By: E Sully
Forum: Porsche 911 Technical Forum 07-26-2020, 01:04 PM
Replies: 28
Views: 881
Posted By E Sully
Just for reference, what engine is in the car? ...

Just for reference, what engine is in the car? There should be an engine type number to the right of the fan housing. The 911/91 was second half of 1973 for the CIS 7R case. This was a better...
Forum: Porsche 911 Technical Forum 07-26-2020, 12:48 PM
Replies: 7
Views: 334
Posted By E Sully
I installed an '86 engine in my 1973. I used my...

I installed an '86 engine in my 1973. I used my '73 SSI's and a low back pressure Bursch Turbo muffler. It ran very smoothly, with and without O2 connected.
https://youtu.be/93wgjvunlTo
I think...
Forum: Porsche 911 Technical Forum 07-10-2020, 01:29 PM
Replies: 10
Views: 632
Posted By E Sully
When I installed the bushings in my car with the...

When I installed the bushings in my car with the engine removed, I had to have a couple of friends lean on the rear to get the bolts in. Without the engine weight it was not going to line up.
...
Forum: 911 Engine Rebuilding Forum 07-02-2020, 06:41 AM
Replies: 9
Views: 809
Posted By E Sully
You would most likely only need top end rebuilt. ...

You would most likely only need top end rebuilt. Valves and guides are main wear I had on my 1986 engine.
Forum: Porsche 911 Technical Forum 06-26-2020, 02:38 PM
Replies: 21
Views: 592
Posted By E Sully
Happy to hear you were able to get those...

Happy to hear you were able to get those injectors. I hope the engine runs great when finished.
Forum: Porsche 911 Technical Forum 06-25-2020, 02:05 PM
Replies: 21
Views: 592
Posted By E Sully
I have purchased a few old injectors over the...

I have purchased a few old injectors over the years. I have been fairly successful using the method of tying the pintel open with fine copper wire, soaking, and back flushing shown in the thread.
Forum: Porsche 911 Technical Forum 06-25-2020, 04:41 AM
Replies: 21
Views: 592
Posted By E Sully
Bob, sent you a PM regarding 3 NOS injectors I...

Bob, sent you a PM regarding 3 NOS injectors I found for sale.
Forum: Porsche 911 Technical Forum 06-24-2020, 05:22 AM
Replies: 21
Views: 592
Posted By E Sully
Tony, just want to add a thanks for all the...

Tony, just want to add a thanks for all the information you supply on the CIS intakes. You and Jims CIS primer have given tremendous aid to all us CIS owners.
Forum: Porsche 911 Technical Forum 06-23-2020, 04:34 PM
Replies: 21
Views: 592
Posted By E Sully
Tony, I would stick with the slide hammer over a...

Tony, I would stick with the slide hammer over a sledge hammer http://forums.pelicanparts.com/support/smileys/smash.gif

As for using silicone, I would think it would work.
Forum: Porsche 911 Technical Forum 06-23-2020, 04:32 AM
Replies: 21
Views: 592
Posted By E Sully
I believe he meant the injector is in the head,...

I believe he meant the injector is in the head, unlike later ones installed in the intake runners.
Here is the factory tool. I believe the thread pitch for the injector is 12 x 1.5mm. You could...
Forum: Porsche 911 Technical Forum 06-19-2020, 05:12 AM
Replies: 2
Views: 215
Posted By E Sully
I would think it should be easy, but you might...

I would think it should be easy, but you might need to change the bumper trim if the width of the bumper horns is different.
Forum: 911 Engine Rebuilding Forum 06-10-2020, 03:35 PM
Replies: 6
Views: 831
Posted By E Sully
This is what my 3.2 looked like from worn valve...

This is what my 3.2 looked like from worn valve guides. I rebuilt the top end.
http://forums.pelicanparts.com/uploads26/Disman2_0111591831836.JPG...
Forum: Porsche 911 Technical Forum 06-09-2020, 07:05 AM
Replies: 17
Views: 1,671
Posted By E Sully
Not sure yundar has the leak at the seam issue,...

Not sure yundar has the leak at the seam issue, or just the flooding issue. If just flooding, it may be able to be fixed without opening the distributor, just freeing the piston and adjusting air...
Forum: Porsche 911 Technical Forum 06-09-2020, 04:54 AM
Replies: 17
Views: 1,671
Posted By E Sully
Jims CIS page is always a good reference. 911...

Jims CIS page is always a good reference.
911 CIS Primer - Index (http://jimsbasementworkshop.com/CIS/)
I have the first generation CIS, so I cannot help with the later Lambda system, but I would...
Forum: Porsche 911 Technical Forum 06-08-2020, 04:53 PM
Replies: 17
Views: 1,671
Posted By E Sully
Do you have a CIS pressure gauge set? Does the...

Do you have a CIS pressure gauge set? Does the plunger in the fuel distributor move smoothly? Are you getting fuel in all the cylinders or just some? You could check to see if you may have some...
Forum: 911 Engine Rebuilding Forum 06-06-2020, 06:56 AM
Replies: 7
Views: 1,047
Posted By E Sully
The pic 4 piece is part #'s 911 108 021 02, 253...

The pic 4 piece is part #'s 911 108 021 02, 253 260 180
It was a drain valve for oil collecting in the bottom of the air box on Carb and CIS intake, 11 and 12.
Not one of my favorite Porsche ideas,...
Forum: Porsche 911 Technical Forum 06-05-2020, 04:10 PM
Replies: 7
Views: 352
Posted By E Sully
When I took my car apart, I found the seat belt...

When I took my car apart, I found the seat belt harnesses were shot, along with previous owners poor speaker wiring. Like most owners, I have everything unplugged....
Forum: Porsche 911 Technical Forum 06-05-2020, 03:22 PM
Replies: 8
Views: 257
Posted By E Sully
When I made that diagram, it was with the...

When I made that diagram, it was with the original harness colors in my 1973.5 CIS, not the diagram colors.
Items I marked NA may have been used in earlier MFI 1973 cars, but not in CIS models....
Forum: Porsche 911 Technical Forum 06-05-2020, 02:11 PM
Replies: 3
Views: 431
Posted By E Sully
Here's a chart for future...

Here's a chart for future reference.http://forums.pelicanparts.com/uploads26/CylinderHeads1591395075.jpg
Forum: Porsche 911 Technical Forum 06-01-2020, 04:10 AM
Replies: 7
Views: 352
Posted By E Sully
Probably the seat, safety belt contacts.

Probably the seat, safety belt contacts.
Forum: Porsche 911 Technical Forum 05-31-2020, 08:02 AM
Replies: 8
Views: 379
Posted By E Sully
Might be time to pull the a arms and install new...

Might be time to pull the a arms and install new rubber bushings while checking the front torsion bars.
Forum: Porsche 911 Technical Forum 05-25-2020, 02:52 PM
Replies: 28
Views: 1,359
Posted By E Sully
The Carrera's are great cars. Motronic works...

The Carrera's are great cars. Motronic works great, but the DME relays can strand you if they fail. Always a good idea to have a spare in the glove box.
Forum: Porsche 911 Technical Forum 05-25-2020, 02:47 PM
Replies: 10
Views: 690
Posted By E Sully
That little c clip is quite a pain. Years back I...

That little c clip is quite a pain. Years back I had to refurbish the distributor in an 86 engine I rebuilt. It sat for many years before I bought it.
Here are before and after pictures. Second...
Forum: Porsche 911 Technical Forum 05-23-2020, 08:30 AM
Replies: 8
Views: 466
Posted By E Sully
I remember the day years back, my brother called...

I remember the day years back, my brother called and told me his wife said she heard what sounded like his car driving away that morning. He looked out the window and his parking space was empty.
...
Forum: Porsche 911 Technical Forum 05-18-2020, 05:35 AM
Replies: 7
Views: 264
Posted By E Sully
Nice to hear it is running well. Just curious,...

Nice to hear it is running well. Just curious, what is the number on your WUR? Is it original or later model.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -8. The time now is 04:52 AM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2020 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.