Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums
Reload this Page Search Results
Register Garage FAQ Social Groups Calendar Search Today's Posts Mark Forums Read


Page 1 of 16 1 2 3 11 Next » Last »
Showing results 1 to 25 of 384
Search took 0.08 seconds. Search: Posts Made By: Peter Graham
Forum: Porsche 924/944/968 Technical Forum 01-25-2021, 10:18 AM
Replies: 5
Views: 329
Posted By Peter Graham
Factory option code M533 - 'ANTI THEFT DEVICE'

Factory option code M533 - 'ANTI THEFT DEVICE'
Forum: Porsche 924/944/968 Technical Forum 01-22-2021, 05:10 AM
Replies: 12
Views: 924
Posted By Peter Graham
Thanks for the link! I looked at the reviews and...

Thanks for the link! I looked at the reviews and the 1 stars were not very complimentary: in your experience, is this a 'flimsy' tool? Does it 'flop around' in use? Inquiring minds...

Thanks,...
Forum: Porsche 912 Technical Forum 01-08-2021, 09:44 AM
Replies: 3
Views: 948
Posted By Peter Graham
The easiest way to replace this rubber is to...

The easiest way to replace this rubber is to loosen the three M6 (10mm ATF) fender bolts accessible from inside the door well (open door and look towards the inside top of the fender) and the one M6...
Forum: Porsche 924/944/968 Technical Forum 01-05-2021, 03:24 PM
Replies: 37
Views: 3,650
Posted By Peter Graham
Wow! Installed: <almost> too much dispersion...

Wow! Installed: <almost> too much dispersion above low beam cutoff, especially from the passenger side. Removed the headlight and the bulb was loose (and was twisted) from its base, causing a light...
Forum: Porsche 924/944/968 Technical Forum 01-05-2021, 12:57 PM
Replies: 37
Views: 3,650
Posted By Peter Graham
Shipped 22 December, USPS finally delivered these...

Shipped 22 December, USPS finally delivered these today!!

Question for those who have installed them: how did you manage to install the rubber dust boot?

Without the boot, the Cibié Z-Beams go...
Forum: Porsche 924/944/968 Technical Forum 12-18-2020, 07:52 AM
Replies: 30
Views: 2,427
Posted By Peter Graham
This thread is more than disheartening... ...

This thread is more than disheartening...

My hatch had delaminated prior to my ownership at the forward/top section; it was causing water leakage, wind noise and misalignment at the hatch pins...
Forum: Porsche 944 Turbo and Turbo S 12-16-2020, 08:06 AM
Replies: 9
Views: 1,578
Posted By Peter Graham
Generally speaking, wire is the wrong implement...

Generally speaking, wire is the wrong implement as flexible drain hoses can be punctured and/or forced off steel nipples; the better alternative is plastic string trimmer line. If it is the ribbed...
Forum: Porsche 944 Turbo and Turbo S 12-11-2020, 10:05 AM
Replies: 8
Views: 1,583
Posted By Peter Graham
When I did that, there was still copious amounts...

When I did that, there was still copious amounts of filter oil that poured out over everything when the filter was removed. If the backflow prevention valve/diaphragm is doing its job, the only...
Forum: Porsche 924/944/968 Technical Forum 12-09-2020, 12:51 PM
Replies: 0
Views: 998
Posted By Peter Graham
Cleaner Oil Filter Change Method?

Cross-post to Turbo/Turbo S forum (http://forums.pelicanparts.com/porsche-944-turbo-turbo-s/1080330-cleaner-oil-filter-change-method.html): I am not sure what models this may work for; worked great...
Forum: Porsche 944 Turbo and Turbo S 12-09-2020, 11:27 AM
Replies: 8
Views: 1,583
Posted By Peter Graham
Cleaner Oil Filter Change Method?

Neither stuffing rags nor holing the filter yielded a 'clean' oil filter change for me so I tried a different technique using a piece of ~6" x ~12" piece of cardstock (from a to-be-recycled zip lock...
Forum: Porsche 924/944/968 Used Parts For Sale & Wanted 11-28-2020, 12:48 PM
Replies: 14
Views: 899
Posted By Peter Graham
MSG sent on power steering pump. Peter

MSG sent on power steering pump.

Peter
Forum: Porsche 924/944/968 Technical Forum 11-28-2020, 08:29 AM
Replies: 37
Views: 3,650
Posted By Peter Graham
Just preordered two sets: one set for the 944...

Just preordered two sets: one set for the 944 turbo, one set for the 68 912 SWT!

Peter
Forum: Porsche 944 Turbo and Turbo S 11-19-2020, 05:12 AM
Replies: 7
Views: 442
Posted By Peter Graham
Brake fluid has no lubricating properties: in...

Brake fluid has no lubricating properties: in spite of other 'recommendations', I would not add any to the PS system (or to motor oil, transmission fluid, etc.). Adding brake fluid to a circulating...
Forum: Porsche 944 Turbo and Turbo S 11-19-2020, 04:28 AM
Replies: 7
Views: 442
Posted By Peter Graham
The key to finding any coolant leak is cleaning...

The key to finding any coolant leak is cleaning all areas (around where leaks are suspected): this will allow the opportunity to see leakage without other factors (slinging, migration) causing fluid...
Forum: Porsche 944 Turbo and Turbo S 11-12-2020, 06:27 AM
Replies: 15
Views: 615
Posted By Peter Graham
I was wrong (again): checking the specs, the dash...

I was wrong (again): checking the specs, the dash lights are dimmable; they just don't dim that much (but still might make a difference on a long night drive). Here's a side-by-side comparison...
Forum: Porsche 924/944/968 Technical Forum 11-11-2020, 07:00 AM
Replies: 37
Views: 3,650
Posted By Peter Graham
Heat gun (or hair dryer): heat will usually make...

Heat gun (or hair dryer): heat will usually make these plastic bit very pliable; if done soon after damage is inflicted (before creases take a set), damage will push out without hardly any residual...
Forum: Porsche 924/944/968 Technical Forum 11-11-2020, 04:26 AM
Replies: 37
Views: 3,650
Posted By Peter Graham
1986 951: PO had an animal strike: front bumper...

1986 951: PO had an animal strike: front bumper covering was repainted but nothing else was repaired. I had the bumper covering off to do other work and rejoined all the fractures using epoxy and...
Forum: Porsche 944 Turbo and Turbo S 11-10-2020, 03:28 AM
Replies: 15
Views: 615
Posted By Peter Graham
I went through this process a couple of years ago...

I went through this process a couple of years ago and found helpful info (I cannot provide links to original sources). I did the following:

Clean the light pipes of all old coating using...
Forum: Porsche 924/944/968 Technical Forum 10-10-2020, 04:58 AM
Replies: 5
Views: 343
Posted By Peter Graham
Before moving on to more effort: shortly after...

Before moving on to more effort: shortly after starting motor (do not allow warm up), use a garden hose (or like) to wet AC/alternator/pwr steering belts: if whine doe not occur upon immediate...
Forum: Porsche 912 Technical Forum 09-30-2020, 01:50 PM
Replies: 1
Views: 571
Posted By Peter Graham
25-spline CVJ's are NLA. Read this thread...

25-spline CVJ's are NLA.

Read this thread (yes it is long a meanders off topic occasionally):
65-68 Lobro Axles (https://www.912bbs.org/forum/threads/65-68-lobro-axles.50093/)

Peter
Forum: Porsche 924/944/968 Technical Forum 09-25-2020, 05:08 AM
Replies: 35
Views: 1,430
Posted By Peter Graham
There is one other issue that has not been...

There is one other issue that has not been mentioned: there are replacement LED/HID bulbs that put a large amount of light just in front of the vehicle. This defeats having 'better' light as the...
Forum: Porsche 924/944/968 Technical Forum 09-22-2020, 01:34 PM
Replies: 35
Views: 1,430
Posted By Peter Graham
Wires look awfully small plus there are only two...

Wires look awfully small plus there are only two relays (I assume one low, one high beam) split between the two headlights (is the harness long enough to span plus locate the relays somewhere...
Forum: Porsche 924/944/968 Technical Forum 09-22-2020, 04:11 AM
Replies: 35
Views: 1,430
Posted By Peter Graham
I dabbled in aftermarket replacement of bulbs in...

I dabbled in aftermarket replacement of bulbs in H4 reflectors designed for incandescent bulbs (912, 951): both LED and HID showed too much scatter on low beams without distinctive cut-off (that...
Forum: Porsche 924/944/968 Technical Forum 09-15-2020, 06:47 AM
Replies: 0
Views: 420
Posted By Peter Graham
Rear Bumper Mounting/Adjustment

I have cut, polished/buffed and waxed my 86 951/944 Turbo (lots of dead paint): during the process, I noticed that the right impact absorber for the rear bumper had collapsed and needed to be...
Forum: Porsche 924/944/968 Technical Forum 08-28-2020, 01:32 PM
Replies: 4
Views: 629
Posted By Peter Graham
Sometimes, the stamp is just down right ugly...

Sometimes, the stamp is just down right ugly (MY86 951/944 Turbo front wheel); I am pretty sure there are multiple versions of the stamp:
http://forums.pelicanparts.com/uploads26/Fox1598646650.jpg
...
Showing results 1 to 25 of 384
Page 1 of 16 1 2 3 11 Next » Last »

 
Forum Jump

All times are GMT -8. The time now is 11:33 PM.

Contact Us - Pelican Parts Catalog for Porsche, BMW, Mercedes-Benz, MINI and More - Archive - Privacy Statement - Terms of Service - Top

 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2020 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.