Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Showing results 1 to 13 of 13
Search took 0.01 seconds. Search: Posts Made By: bwrichardson

Forum: Porsche 911 Technical Forum

11-24-2023, 06:58 PM

Replies: 16

Shipping my 911 cross country

Views: 967

Posted By bwrichardson

Paul, Five weeks ago, I successfully...

Paul,

Five weeks ago, I successfully transported my 911SC and another car from remote NW Montana to NE Ohio with Intercity Lines. They were very helpful and accommodating with my needs. Scott,...

Forum: 911 Engine Rebuilding Forum

05-18-2017, 01:27 PM

Replies: 9

1983 911 SC engine wiring harness

Views: 2,044

Posted By bwrichardson

Am in need of one.

Am in need of one.

Forum: 911 Engine Rebuilding Forum

05-18-2017, 11:30 AM

Replies: 9

1983 911 SC engine wiring harness

Views: 2,044

Posted By bwrichardson

1983 911 SC engine wiring harness

I've been unable to have timmy2 respond to several emails and PMs over several weeks to obtain information about the engine wiring harness. Are there other avenues of communication with him? I am...

Forum: 911 Engine Rebuilding Forum

03-09-2017, 03:04 PM

Replies: 3

'83 911 SC 3.0 L rebuild 142,000 miles

Views: 566

Posted By bwrichardson

Thank you, Bruce. I live in the frontier of...

Thank you, Bruce.
I live in the frontier of Montana; can any machine shop the will weld aluminum do the job? Or ship it off to, say, Ollie's?

Forum: 911 Engine Rebuilding Forum

03-09-2017, 12:49 PM

Replies: 3

'83 911 SC 3.0 L rebuild 142,000 miles

Views: 566

Posted By bwrichardson

'83 911 SC 3.0 L rebuild 142,000 miles

http://forums.pelicanparts.com/uploads26/IMG_02891489092046.JPG
During disassembly, I found this. This does not appear to be a fresh break. Fix with GB Weld and tighten the nut carefully or weld...

Forum: Porsche 911 Technical Forum

01-29-2017, 03:46 PM

Replies: 4

Torin Jacks T26801 Engine Stand - Will my yoke fit?

Views: 578

Posted By bwrichardson

I have both-excellent fit.

I have both-excellent fit.

Forum: Porsche 911 Technical Forum

03-09-2015, 07:45 PM

Replies: 22

Front Bearing Race removal

Views: 2,480

Posted By bwrichardson

With no cutouts, heating/freezing was not...

With no cutouts, heating/freezing was not effective and I have neither a collection of hardened washers nor a press. I drove the 90 miles to a "Porsche" shop and for gas and $40 had the old races...

Forum: Porsche 911 Technical Forum

01-31-2015, 09:35 PM

Replies: 7

front wheel hub/(inner bearing) outer race question

Views: 616

Posted By bwrichardson

Thanks jayson2guy. If I don't need to replace...

Thanks jayson2guy. If I don't need to replace the wheel hubs, I will have a machinist shop remove the old and reset my new races. My concern is the "burr" on the hub and if the new race will be...

Forum: Porsche 911 Technical Forum

01-31-2015, 07:33 PM

Replies: 7

front wheel hub/(inner bearing) outer race question

Views: 616

Posted By bwrichardson

Thank you. So I do not have to worry about the...

Thank you. So I do not have to worry about the "burr" that is already formed on the hub at the inner contact point of the outer race? There are no notches which would allow a pin punch to get a...

Forum: Porsche 911 Technical Forum

01-31-2015, 06:43 PM

Replies: 7

front wheel hub/(inner bearing) outer race question

Views: 616

Posted By bwrichardson

front wheel hub/(inner bearing) outer race question

'83 SC Targa 142000 miles Since I was replacing the ball joints, tie rods/tie rod ends (Turbo),and struts, I thought replacing the front bearings was appropriate. When I got everything apart and...

Forum: Porsche 911 Technical Forum

02-18-2014, 08:33 PM

Replies: 6

Blown fuse #5

Views: 932

Posted By bwrichardson

Replaced the existing incorrect relay...

Replaced the existing incorrect relay (91161510801 fuel pump) with the correct 91161510901 relay and problem resolved! Thanks, again.
Bruce

Forum: Porsche 911 Technical Forum

02-18-2014, 07:33 AM

Replies: 6

Blown fuse #5

Views: 932

Posted By bwrichardson

Thank you Fred, PORWOLF, and T77911S.! I will...

Thank you Fred, PORWOLF, and T77911S.! I will replace the #2 relay and report. Fred, I missed seeing the gray wire invisibly tucked behind the yellow wire to the R low beam and missed how it was...

Forum: Porsche 911 Technical Forum

02-17-2014, 11:05 PM

Replies: 6

Blown fuse #5

Views: 932

Posted By bwrichardson

Blown fuse #5

1983 911 SC targa, stock, 142000 miles, new to me summer of '13.
With the ignition on Acc or On (engine running): when the low beam lights are on, the right low beam fuse #5 fails when the fog lamp...

Showing results 1 to 13 of 13

Forum Jump

All times are GMT -8. The time now is 01:46 AM.