Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Showing results 1 to 9 of 9
Search took 0.01 seconds. Search: Posts Made By: Ed_914

Forum: 911 Engine Rebuilding Forum

03-24-2017, 05:22 AM

Replies: 24

Soda blasting case question

Views: 3,050

Posted By Ed_914

No, it is a 3.0 sc 930/10 the vapourblasting and...

No, it is a 3.0 sc 930/10 the vapourblasting and the WD40 to protect it for storage ,till I build my 3.2 ss with nickies, gives this very nice colour

Forum: 911 Engine Rebuilding Forum

03-24-2017, 03:41 AM

Replies: 24

Soda blasting case question

Views: 3,050

Posted By Ed_914

My vapour blasting guy ,ccauquablasting uk, has...

My vapour blasting guy ,ccauquablasting uk, has done mine and told me to clean it well before building the engine. He spent a long time getting ride of the residue but put the owners on me to be...

Forum: 911 Engine Rebuilding Forum

02-20-2017, 08:29 AM

Replies: 777

The Complete Engine Sealant Thread...

Views: 198,678

Posted By Ed_914

Don't know if it is a good idea but i would oil...

Don't know if it is a good idea but i would oil stone the 2 halves and create a flat surface

Forum: 911 Engine Rebuilding Forum

08-16-2016, 10:35 AM

Replies: 35

80SC RoW rebuild: 8 broken lower head studs! 200K KM

Views: 4,127

Posted By Ed_914

Good point, in my case it was a full tear down.

Good point, in my case it was a full tear down.

Forum: 911 Engine Rebuilding Forum

08-16-2016, 09:30 AM

Replies: 35

80SC RoW rebuild: 8 broken lower head studs! 200K KM

Views: 4,127

Posted By Ed_914

Hi Tom, I didn't have any problems but make...

Hi Tom,

I didn't have any problems but make sure you clean the sides and the top to bare metal ,so the weld will be penetrating the stud and the nut. Using a non galvinised nut is best(gives less...

Forum: 911 Engine Rebuilding Forum

08-16-2016, 08:11 AM

Replies: 35

80SC RoW rebuild: 8 broken lower head studs! 200K KM

Views: 4,127

Posted By Ed_914

I cleaned the stud with a dremel to bare clean...

I cleaned the stud with a dremel to bare clean metal. Then I put a big washer over it ,with the perfect size hole and then I did put a big nut M12 over it. Protect your case with fire resistant cloth...

Forum: 911 Engine Rebuilding Forum

04-25-2016, 11:56 PM

Replies: 32

2.4T Rebuild - Many Questions

Views: 3,348

Posted By Ed_914

Frank, Try to find a nut that is slightly...

Frank,

Try to find a nut that is slightly larger than the stud and has no protection on it i.e. zinc or plating. Clean the stud where you are welding. I used a sanding disk for that. Then MIG weld...

Forum: 911 Engine Rebuilding Forum

04-25-2016, 06:35 AM

Replies: 32

2.4T Rebuild - Many Questions

Views: 3,348

Posted By Ed_914

I welded the nut 2 inches from the case so I...

I welded the nut 2 inches from the case so I could weld from both sides. Make sure you protect your case while welding. Heating the case is the mean trick here. It took 15 min of heating.

Forum: 911 Engine Rebuilding Forum

04-05-2016, 11:45 AM

Replies: 32

Cannot Remove Last Headstud

Views: 2,234

Posted By Ed_914

I slid a nut over the stud till about 2 inches...

I slid a nut over the stud till about 2 inches above the case and mig welded it from both sides. heated the case 15 minutes with the torch. (use plain steel nut). Put a ring spanner and an 1.5 foot...

Showing results 1 to 9 of 9

Forum Jump

All times are GMT -8. The time now is 10:13 PM.