Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Showing results 1 to 10 of 10
Search took 0.01 seconds. Search: Posts Made By: sundog

Forum: 911 Engine Rebuilding Forum

09-19-2006, 09:32 PM

Replies: 40

964 Engine - What is the realistic redline for bottom end?

Views: 7,582

Posted By sundog

The force/stress on the connecting rod is...

The force/stress on the connecting rod is proportional to the square of the RPM of the engine. The fatigue life curves for the casting metals used degrade exponentially with this applied stress. This...

Forum: 911 Engine Rebuilding Forum

09-19-2006, 09:13 PM

Replies: 4

964 Oil Pump Question

Views: 813

Posted By sundog

If you need to replace the oil pump, and are...

If you need to replace the oil pump, and are unhappy with the cost, ~1400$, you can buy a new GT3 oil pump for about $600, and have one of the webs on the 964 case machined down. You get a secondary...

Forum: 911 Engine Rebuilding Forum

02-06-2006, 10:18 AM

Replies: 27

Anderson/Woods rebuilding course...a short review

Views: 4,490

Posted By sundog

I'm the one with the 964 that is on it's 3rd...

I'm the one with the 964 that is on it's 3rd rebuild. In closer examination of the reciepts from the previous 2 rebuilds, I have found that the part numbers used for the rod bearings are...

Forum: 911 Engine Rebuilding Forum

02-06-2006, 10:06 AM

Replies: 5

Rebuilding 964 oil pump

Views: 1,274

Posted By sundog

Rebuilding 964 oil pump

Well, this weekend while disassembling my oil pump to check for damage from the spun bearing in my engine, I managed to bugger up one of the bushings on the drive shaft of the oil pump. Does anybody...

Forum: 911 Engine Rebuilding Forum

12-28-2005, 10:20 PM

Replies: 1

Rod Bearing Part Number Question

Views: 637

Posted By sundog

Rod Bearing Part Number Question

Ok, just trying to be thorough about my rebuild. In the PET, the connecting rod bearing for my 1991 C2 has a part number of 930-103-147-00. However, I have found that the part number used on both of...

Forum: 911 Engine Rebuilding Forum

07-31-2005, 09:00 AM

Replies: 20

Spun Bearing ARRGGHHH

Views: 2,924

Posted By sundog

I was told by the sales person that there was...

I was told by the sales person that there was sugar in the gas tank, and the insurance company paid for a complete rebuild. No collision damage, as the car has a clean carfax.

Forum: 911 Engine Rebuilding Forum

07-30-2005, 11:14 PM

Replies: 20

Spun Bearing ARRGGHHH

Views: 2,924

Posted By sundog

The $20K rebuild was an insurance rebuild by the...

The $20K rebuild was an insurance rebuild by the previous owner. Basically a "new" engine, clearly not done correctly though.

Forum: 911 Engine Rebuilding Forum

07-29-2005, 11:41 AM

Replies: 20

Spun Bearing ARRGGHHH

Views: 2,924

Posted By sundog

I was told by the rebuilder that the crank was...

I was told by the rebuilder that the crank was bent by .005, and that it needed to be straightened or replaced. I chose replacement. I still have it in my office, and the surfaces do not look bad. Is...

Forum: 911 Engine Rebuilding Forum

07-28-2005, 10:59 AM

Replies: 20

Spun Bearing ARRGGHHH

Views: 2,924

Posted By sundog

Sorry for the lack of details, 1991 C2...

Sorry for the lack of details,

1991 C2 Tiptronic. 3.6 Litre engine. Last rebuild done at T&D performance in Campbell CA. Replaced oil pump, Crankshaft with used one, old one was "bent".

Forum: 911 Engine Rebuilding Forum

07-28-2005, 10:31 AM

Replies: 20

Spun Bearing ARRGGHHH

Views: 2,924

Posted By sundog

Spun Bearing ARRGGHHH

I have recently had a noise in the engine, light knocking at 4000 rpm. I have taken a look in my oil filter to see if there is a problem, and loe and behold, Copper in the oil filter. This has...

Showing results 1 to 10 of 10

Forum Jump

All times are GMT -8. The time now is 10:34 AM.