Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Showing results 1 to 9 of 9
Search took 0.01 seconds. Search: Posts Made By: BSMotorsport

Forum: 911 Engine Rebuilding Forum

12-02-2017, 01:46 AM

Replies: 1,352

964 3.3 Turbo EFI Conversion using Syvecs (Life Racing) Engine Management

Views: 277,594

Posted By BSMotorsport

Hi when you get it all finished if you want to...

Hi when you get it all finished if you want to run and map it in the test cell before re fitting to car drop me a line i am just carrying out two single turbo conversion and a twin all to go to...

Forum: Porsche 911 Technical Forum

11-01-2014, 05:42 AM

Replies: 12

Porsche 911 Ring & Pinion

Views: 1,118

Posted By BSMotorsport

Hi I am just making new Ring and pinion slightly...

Hi I am just making new Ring and pinion slightly lower ratio @ 5:1 7/35 or I probably have a std 7/31 mech drive set if you get stuck
Neil

Forum: Porsche 964 & 993 Technical Forum

08-28-2012, 06:37 AM

Replies: 0

993rsr bodywork supplier

Views: 554

Posted By BSMotorsport

993rsr bodywork supplier

Iam looking for a supply of 993RSR body work parts can anyone help europe or uk would be prefered due to shipping charges.

Forum: 911 Engine Rebuilding Forum

09-04-2011, 01:43 PM

Replies: 1,352

964 3.3 Turbo EFI Conversion using Syvecs (Life Racing) Engine Management

Views: 277,594

Posted By BSMotorsport

Hi Spencer. I had the engine that chris was...

Hi Spencer.
I had the engine that chris was refering to on my dyno and the numberes were all good car drives like a dream, the grate think is the low down boost well below 3000 if you have any...

Forum: 911 Engine Rebuilding Forum

09-04-2011, 01:08 PM

Replies: 4

Increase power 3.2 l engine

Views: 1,107

Posted By BSMotorsport

Hi i have a friend that has a very good set of...

Hi i have a friend that has a very good set of 100mm pistons and liners and also crank cases that have all ready been bored to take the liners, and a set of twin plug ported and polished heads, the...

Forum: Porsche 911 Technical Forum

10-13-2009, 06:04 AM

Replies: 5

Crankshaft pulley question

Views: 506

Posted By BSMotorsport

Would not advise the Impact Wrench, i have been a...

Would not advise the Impact Wrench, i have been a engine builder for over 30 years, impact wrenches and crank shafts dont go together!!

Forum: Porsche 911 Technical Forum

10-13-2009, 01:09 AM

Replies: 5

Crankshaft pulley question

Views: 506

Posted By BSMotorsport

Hi Jason, you can hold the flywheel by locking...

Hi Jason, you can hold the flywheel by locking the startor ring gear with a flywheel lock, i can send you a photo if you want but the easiest way is to just pop off the clutch its only 9 bolts and...

Forum: Porsche 911 Used Parts For Sale & Wanted

10-13-2009, 12:51 AM

Replies: 5

WTB: TWO Sets Motorsport 911 RSR Rocker Arms (Nitrided)

Views: 702

Posted By BSMotorsport

Hi but you would never know where the parts were...

Hi but you would never know where the parts were - are hiding if you ask !
I also have if any one is intrested parts for 2.8 RSR Engine / Oil Pump kits for 915 Gearbox.
Regards Neil

Forum: Porsche 911 Used Parts For Sale & Wanted

10-09-2009, 09:52 AM

Replies: 5

WTB: TWO Sets Motorsport 911 RSR Rocker Arms (Nitrided)

Views: 702

Posted By BSMotorsport

Race 911 rocker shafts

Hi i have race rocker shafts in stock along with other special race parts you can mail me at Neil@bsmotorsport.co.uk or Neil@mrzapcat.com

Regards Neil

Showing results 1 to 9 of 9

Forum Jump

All times are GMT -8. The time now is 04:53 PM.