Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Page 1 of 7

Last »

Showing results 1 to 25 of 157
Search took 0.03 seconds. Search: Posts Made By: lr172

Forum: 911 / 930 Turbo & Super Charging Forum

01-04-2011, 01:10 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

It is a 3076 and it may be a bit on the small...

It is a 3076 and it may be a bit on the small side and I may lose a little at the top. However, given my driving habits, I would much rather have the sooner boost and give up a bit at redline. I...

Forum: 911 / 930 Turbo & Super Charging Forum

01-04-2011, 01:06 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Thanks for sharing. I am currently running 20*...

Thanks for sharing. I am currently running 20* at .6 and at the rate of decline that I use, I would be at 18 at .7. Maybe I'll drop a point or two and see what I lose. What did the detonation...

Forum: Porsche 911 Technical Forum

01-03-2011, 09:34 PM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

an update on my progress with detonation ...

an update on my progress with detonation

http://forums.pelicanparts.com/911-930-turbo-super-charging-forum/577542-turbo-recommendation-2.html#post5762315

I never did get a good compression...

Forum: 911 / 930 Turbo & Super Charging Forum

01-03-2011, 09:32 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Thought I would post my results I wound up...

Thought I would post my results

I wound up getting a slightly used GT30R (100 miles) with a .63 housing for a good deal. While I haven't had a great deal of testing due to weather, I start...

Forum: Porsche 911 Technical Forum

12-21-2010, 12:35 PM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

I have been following the model that Procomp used...

I have been following the model that Procomp used for the 3.2 with 9.5:1, which was .5 bar w/o intercooler and .7 with. Several have run this config without issue. Going to .6 bar without the i/c...

Forum: Porsche 911 Technical Forum

12-20-2010, 09:00 PM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

I checked the timing on the #1 side tonight and...

I checked the timing on the #1 side tonight and came up with 1.42mm. According to Bentley the target is 1.25 and the tolerable range is 1.1-1.4. If I am thinking about this correctly, this leaves...

Forum: Porsche 911 Technical Forum

12-20-2010, 12:44 PM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

Just to verify, can someone tell me the amount of...

Just to verify, can someone tell me the amount of valve lift I should measure at #1 TDC for cam timing on a '88 3.2?

Thanks,

Larry

Forum: Porsche 911 Technical Forum

12-20-2010, 09:14 AM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

I never did do a compression test on the motor...

I never did do a compression test on the motor before putting the turbo on. However the P/O did a leakdown and all were in the 8-10% range similar to what I observed.

I put the turbo on as well a...

Forum: Porsche 911 Technical Forum

12-19-2010, 07:57 PM

Replies: 12

Please help with Low Compression

Views: 1,106

Posted By lr172

Please help with Low Compression

Last year I put a turbo on my 3.2. This year I just don't seem to have the power that I had when I first put the turbo on. I pulled all the plugs and I apparently have some detonation that I need...

Forum: 911 / 930 Turbo & Super Charging Forum

12-02-2010, 04:29 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Just read it now. Seems that the BB's can make a...

Just read it now. Seems that the BB's can make a substantial difference in spool up. That was the first data point where someone tested a like turbo with and without BB. It was enough to push me...

Forum: Porsche 911 Technical Forum

12-02-2010, 04:19 PM

Replies: 3

HELP: CV joint boot change

Views: 1,014

Posted By lr172

I replaced the outer boot on my '88 when I had...

I replaced the outer boot on my '88 when I had the engine out. I bought a boot at a local parts store for $25. Carquest I think. It was a German mfg part and came with lube and clamps. I thought...

Forum: 911 / 930 Turbo & Super Charging Forum

12-02-2010, 11:48 AM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Last night I pulled the filter off and it appears...

Last night I pulled the filter off and it appears there is enough wear in bushings to allow the blades to just touch the bore. No significant wear noticeable on the housing. This would explain the...

Forum: Porsche 911 Technical Forum

12-01-2010, 09:50 PM

Replies: 5

Resistor Plugs

Views: 728

Posted By lr172

Resistor Plugs

I am going to colder plugs to accomodate my turbo. I naturally bought resistor plugs (BPR7ES) to protect the EFI. Then I reliazed that I also have resistance built into the rotor. It appears that...

Forum: 911 / 930 Turbo & Super Charging Forum

11-30-2010, 08:40 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Thanks for the reply. If all of these will spool...

Thanks for the reply. If all of these will spool up at 3K it makes me wonder why I am spooling at 4K with the T04E. It doesn't seem that it is THAT different. I wonder if something else is wrong...

Forum: 911 / 930 Turbo & Super Charging Forum

11-30-2010, 02:57 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

For the 60-1, my calcs show my flow at 3000 with...

For the 60-1, my calcs show my flow at 3000 with 10 PSI to be 17 lb. If the turbo spools at 3000, that leaves me very close to the surge line at the 1.68 pressure ratio. I am going to roll the dice...

Forum: 911 / 930 Turbo & Super Charging Forum

11-28-2010, 08:46 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

911st, Thanks for posting the ideas and the...

911st,

Thanks for posting the ideas and the content. I took a look at several maps and my T04E is WAY off. No wonder the MAT is getting so high. The 60-1 is too close to the surge line. ...

Forum: 911 / 930 Turbo & Super Charging Forum

11-28-2010, 01:02 PM

Replies: 72

Please help me tune my 3.2 Turbo Conversion

Views: 5,491

Posted By lr172

Sorry. Haven't been here in a while. Was...

Sorry. Haven't been here in a while. Was working a different project. I built a 65 Cobra replica.

I ended up putting in a Megasquirt system to get control over the fuel flow and Advance tables....

Forum: 911 / 930 Turbo & Super Charging Forum

11-28-2010, 12:51 PM

Replies: 27

Turbo Recommendation

Views: 2,944

Posted By lr172

Turbo Recommendation

A year ago I added a turbo to my 3.2 carrera along with a Megasquirt EFI (still 9.5:1 CR). It runs great, but I don't get full boost (.6 BAR for me) until 4100 RPM. It has an old T3/T04E with a 60...

Forum: 911 / 930 Turbo & Super Charging Forum

11-27-2010, 08:23 PM

Replies: 372

Top End Rebuild and Turbo Project underway

Views: 56,251

Posted By lr172

My steady cruise MAT will vary, but I typically...

My steady cruise MAT will vary, but I typically see about a 50*+ rise when I go from a temp stable cruise to a WOT run up to 6K. My MAT typically runs 130-150 in cruise in the warm months. Some of...

Forum: 911 / 930 Turbo & Super Charging Forum

11-27-2010, 03:57 PM

Replies: 372

Top End Rebuild and Turbo Project underway

Views: 56,251

Posted By lr172

I put a Megasquirt on my 3.2 after having...

I put a Megasquirt on my 3.2 after having problems with unstable/undesirable AFRs using Todd's chip. Total cost was less than $500 and a fun project. Wiring was unpleasant, but the only real hard...

Forum: 911 / 930 Turbo & Super Charging Forum

11-27-2010, 03:32 PM

Replies: 372

Top End Rebuild and Turbo Project underway

Views: 56,251

Posted By lr172

I am running MS2 wiht MSExtra 2.1.0. I added an...

I am running MS2 wiht MSExtra 2.1.0. I added an output circuit to the V3.0 board (simple pull up cicuit with a tansistor in the Proto area) and use the MSExtra Output function to control it. This...

Forum: 911 / 930 Turbo & Super Charging Forum

11-27-2010, 03:23 PM

Replies: 372

Top End Rebuild and Turbo Project underway

Views: 56,251

Posted By lr172

I am also running a megasquirt in my 3.2 carrera...

I am also running a megasquirt in my 3.2 carrera (stock 9.5:1). I do not have an intercooler or meth yet (planning one or the other this winter) and run .6 BAR without any noticeable knocking. Can...

Forum: Porsche 911 Technical Forum

11-18-2010, 02:51 PM

Replies: 11

Looking for help identify elec conn in front compartment

Views: 711

Posted By lr172

Thanks for all of your assistance here. I...

Thanks for all of your assistance here. I appreciate it.

Forum: Porsche 911 Technical Forum

11-18-2010, 01:29 PM

Replies: 11

Looking for help identify elec conn in front compartment

Views: 711

Posted By lr172

Thanks for looking. On your car, was one a male...

Thanks for looking. On your car, was one a male and one a female. If not, how were they connected

Thanks again for your help.

Larry

Forum: Porsche 911 Technical Forum

11-18-2010, 12:44 PM

Replies: 11

Looking for help identify elec conn in front compartment

Views: 711

Posted By lr172

Thanks for posting that dia; It helps. I went...

Thanks for posting that dia; It helps. I went and followed the wire with the female connector and it goes to the windshield washer outlet on that side, so it must be a spare, as I don't have heated...

Showing results 1 to 25 of 157

Page 1 of 7

Last »

Forum Jump

All times are GMT -8. The time now is 05:23 PM.