100 lb R-11 drum. Low pressure refrigerant primarily for centrifugal chillers.
I have moved more than 1 or 2 of those...
I had a really cool little 10 lb drum that I had used for flushing small systems that had a bad burnout.

Had some time off for the holidays and had some "honey do's" lined up. Unfortunately came down with a nasty cold/flu and have been on the couch.

But I feel like I'm getting stuff done by watching "The Repair Shop" on Netflix, a British show where they repair antique family heirlooms. Pretty neat.

https://www.netflix.com/title/81224128

My mother-in-law has been complaining of how low the washer and dryer are. Looked online and metal bases to fit the units were over $500.00.
I had a sheet of 3/4 Advan Tech in the shed..a few hours and some scrap lumber turned into this. She is going to be thrilled when she gets back from Colorado next week.http://forums.pelicanparts.com/uploa...1577401696.jpg

http://forums.pelicanparts.com/uploa...1577401958.jpg


SmileWavy

Anyone else bought those Ikea floor lamps with disintegrating base plates, well, I have 2 of them... one with the base falling apart, another with a busted switch ... instead of tossing both, made one good lamp out of the two. Thought that was a neat trick.

No pictures, but installed a new battery on my motorcycle.

Nice! Batteries are important! :p

My Honda didn't come with any turn signals so I found some at a decent price on eBay and they are in pretty good shape. Will install at some point but I did check the wiring harness to see if the wires were still there to connect.

Looks good on the rears but I have to spend more time on checking out the front ones as the wiring harness is buried a little more.

http://forums.pelicanparts.com/uploa...1577582519.JPG

http://forums.pelicanparts.com/uploa...1577582519.JPG

Bike still has it's tool kit and little holder with spare fuses.....:)

http://forums.pelicanparts.com/uploa...1577582519.JPG

http://forums.pelicanparts.com/uploa...1577582519.JPG

A 6' piece of 3" tubing came today to help with boat trailer restoration work.....closing in on finishing that job.....

http://forums.pelicanparts.com/uploa...1577582765.JPG

Looking at changing out transmission fluids/filter, along with rear end lube, and engine oil filter on my 1996 4.9L I6 today. Thinking of going full synthetic with my Christmas gift cards.

Transmission is going back in the 2000 V6 Camry one way or another. The tilt on the trans jack broke yesterday, causing the transmission jack plate to suddenly roll towards the fire wall. Thank the lord I had the trans strapped securely and the jack didn't tip over.

Now it's a combination of jacks to get it lined up and mated to the engine. Probably going to get some long guide bolts first. I'm working on damp soil, so 3/4 inch ply wood has been laid under the trans jack.

Any help is appreciated!

Broke out the mini ex and dug about 50' of trench for a new drain from the house to a new main outlet I had installed a month ago. Weather was too nice not to be outside doing something! But digging in the dirt??

Baz, did you order that steel on-line? From where?

Hi Paul.

Got it through Amazon, believe it or not.

Was having trouble finding some locally and Amazon had it for what I considered a decent price - and delivered right to my door.

RMP Hot Rolled Carbon Steel Square Tube, 3 Inch Width x 3/16 Inch Wall, 72 Inch Length, Mill Finish

$116.61 delivered.

Also got some flat and angle iron pieces.

I'm sure there are places (fabrication/weld shops) you could buy from too but man sometimes running all over the place and you still can't get what you want. Gets frustrating and way too time consuming. I'd rather pay a few more dollars and get what I need - especially delivered.

I'm spraying them with cold zinc galv spray too....

http://forums.pelicanparts.com/uploa...1577667693.JPG

Thanks Baz. Amazon...I should have known. :rolleyes:

I don't know why the rolled eyes. Sheesh.....

I tried to source it locally and even asked my mechanic if he could get these pieces. He knew a guy, etc etc.

Two freaking weeks went by and nothing.

I even asked a couple local trailer builders.

Not my fault if I resorted to Amazon.

FWIW, it did come from an American company - made in the USA:

http://forums.pelicanparts.com/uploa...1577670751.JPG

I meant no offence by the eye roll. I was implying how I should have known it could be found on Amazon. ;)

OK gotcha.

It's truly amazing what you can get through Amazon.

I really do try to use local merchants though as much as possible - but if I run into an obstacle - it's nice to have online options - like Amazon.

This Prime membership is the best investment I have made in many moons, too. Really helps with shipping costs.

Had to work today but got home in time to continue work on my boat trailer.

Got the front brace finished and ready to install tomorrow - it will hold my winch stand.

The leftover piece of 3" tubing will also be installed tomorrow further back and will hold my keel roller.

After that it will be a new set of lights and then the trailer is (finally) done and I can focus on the boat. :D

http://forums.pelicanparts.com/uploa...1577839012.JPG

http://forums.pelicanparts.com/uploa...1577839012.JPG

http://forums.pelicanparts.com/uploa...1577839012.JPG

http://forums.pelicanparts.com/uploa...1577839012.JPG

I started building a chopper minibike. I have all the parts so figured i might as well build something
http://forums.pelicanparts.com/uploa...1577849210.JPG

My neighbor asked me to re solder on the wheel of this old Jeep pin he got it from a nurse shortly after the war. Im into jeeps i have a 1946 cj2a. I wanted one so i copied it and made my own it came out pretty good but its not easy soldering together those little pieces.

http://forums.pelicanparts.com/uploa...1577934003.JPG
http://forums.pelicanparts.com/uploa...1577934003.JPG

Finished up the rust repair and third light replacement on the Silverado today. Used an aftermarket LED fixture. Still have some compounding and touching up to do.

http://forums.pelicanparts.com/uploa...1578098573.JPG

http://forums.pelicanparts.com/uploa...1578098573.JPG

http://forums.pelicanparts.com/uploa...1578098573.JPG

http://forums.pelicanparts.com/uploa...1578098573.JPG

Here's how the boat trailer repairs came out. New torsion axle, new wheels, new jack, new tongue, new fabricated keel roller brace, new keel roller, new fabricated winch stand brace, new winch stand, and new winch.

Tomorrow I will install new LED trailer lights. I got these cool little cable ties with push in clips to attach to the trailer frame.

http://forums.pelicanparts.com/uploa...1578101738.JPG

http://forums.pelicanparts.com/uploa...1578101738.JPG

http://forums.pelicanparts.com/uploa...1578101738.JPG

http://forums.pelicanparts.com/uploa...1578101738.JPG

http://forums.pelicanparts.com/uploa...1578101738.JPG

Tried to put a new Kenwood radio in the E36 M3 after the old JVC died. Jeez, it should have been a simple 2 hour job, even with having to add a new Sirius module, as they keep changing the connections, but NOOOOOOOOO!

Wired up power and speaker connections, unit powers up fine, but absolutely no sound. 5 hours later, after disassembling about half the car, and still no sound, I say eff it and decide it's Yuengling time. Apparently, this activated some dormant neurons, so I fired up Google and re-discovered that this car has a built in amp that has to be triggered. Since I had ripped out all the wiring I had just done, I got to do it all again AND the blue amp wire. Works fine now, except the antenna connector broke off, so I get to fix that, too. Then, the thunderstorm rolled in..............

My fixit day was all trivial stuff but it felt satisfying to get a whole lot of it done in 4 hours.

I took the kids to their college apartment on Saturday. This is my daughter's place and my son is moving in with her. It's a standard issue cheapo two bedroom student place in Eugene OR, meaning there's a lot of little things broken and the management company won't fix anything that doesn't actually make it uninhabitable. We get there, move in my son's stuff, I'm supposed to spend the night, but I look around and see dozens of little things that need doing. So I drive 2 hours home, the next morning I load some tools and drive 2 hours back. Start checking things off the list at 10:30 am, done and headed home at 2:30 pm.

What I did.
1. installed door chain (wife insists, for safety)
2. hung mirror
3. reversed refrigerator doors
4. installed 100 w daylight LED bulbs in bedrooms (had to extend the threaded whateveritis that the shade screws to, to fit the larger bulbs)
5. set up the espresso machine
6. oiled kitchen cabinets (they are utter crap cabinets, falling apart, but still do look a little better now)
7. oiled dining table
8. fixed hall closet door (it wouldn't close)
9. fixed bedroom #1 closet door (to the extent possible, it’s really a mess, but it closes now)
10. fixed outside light (wife insisted on this too, safety again)
11. installed daylight LED bulb in hall fixture (apartment was too dim, needed more “happy light”)
12. re-attached kitchen drawer face (glue, clamps, nails) - this isn't the first drawer face that's fallen off!
13. installed magnetic knife holder
14. installed 100 w equivalent daylight LED bulbs in kitchen (more happy light, had to extend the whateveritis)
15. installed brighter daylight LED bulbs in bathroom
16. put up hooks at entry to hang keys
17. set up dual monitors for son
18. pumped bike tires
19. fixed a broken "mood lamp" thingy
20. installed new swivel spray head for kitchen faucet (it was simply splashing water all over)

Jyl, I;m impressed. Those are the sort things I do. But I'd call that three weeks hard labour.

https://media.giphy.com/media/FzV61A4U3guAw/giphy.gif

Dang John.......putting us all to shame! :cool:

Trying to attend to my Silverado cosmetics - the little cab badges have melted on me so I found some on eBay and got the first one today. The other arrives later in the week.

Little things I know - but they all add up. I want to restore the truck to it's magnificent original state. :p

The old ones - yuck!:

http://forums.pelicanparts.com/uploa...1578364548.JPG

http://forums.pelicanparts.com/uploa...1578364548.JPG

Replacement - ahhhh!:

http://forums.pelicanparts.com/uploa...1578364548.JPG

Met a local guy who wants to install an engine conversion in his Vanagon. I gave him a test drive in my converted van, he decided to do it, I'm like "how would you like to borrow my engine hoist" which he heard as "such a generous offer" and I meant as "get this effing thing out of my garage for awhile".

Busy day today. Getting my '83 SC ready to visit my mechanic so he can get the engine back up and running plus a few other things. Transport supposed to take place Monday.

I power washed my boat and tried to use my new foam cannon but ultimately it was easier and more effective to just load some cleaner in a little 2 gallon pump sprayer I have and use that to apply the cleaner and later blast everything clean with my washer.

Here is the Bimini top I cleaned on my driveway. I will be installing new deck hinges for it next week before re-installing.

Also some finger ratchets I bought. Never used them before but thought they might come in handy. I got the 3 pack - 1/4, 3/8, and 1/2 inch drives.

http://forums.pelicanparts.com/uploa...1578777687.JPG

http://forums.pelicanparts.com/uploa...1578777687.JPG

http://forums.pelicanparts.com/uploa...1578777687.JPG

http://forums.pelicanparts.com/uploa...1578777687.JPG

This morning I.....

Refitted the refurbished rear prop shaft to my Toyota 4Runner, drives so much smoother, I can see stuff in the rear view mirror now :D but think the rear axle links need new bushes as there is still a slight vibration under acceleration :confused:

Also fitted new front pads/discs to Mrs Ahab's Fiat 500 Twinair. It's great fun working on a toy sized car, everything is like half scale to my truck, parts cheap too, brake discs were $10 each :eek::cool:

Replaced my submersible well pump because I had nothing better to do with my time today. For the real story, I woke up around 5:30, made a cup of coffee, was sitting in my family room surfing the web when I heard my well pump kick on. Then it kicked on again.... and then again... and I thought "WTH? there's no one up but me!?" Turns out the check valve in my pump went bad which was allowing water pressure to build in the pressure tank but when the pump shut off it would back flow to the well pretty quickly then the pump would come back on. What Fun!!

For my next "because I'm bored" fix... a new well pressure tank which will require moving an iron filter to make room for it because the new tank is 22" and there's only 21" between the iron filter and the water heater.
For the real reason, after installing the pump, I checked the run time from cut in to cut out... 36 seconds. A pump should run for a minute or more. If it doesn't you'll decrease the life of the pump. If I shoot for the 2 minute run time the guy I bought the pump from recommends, I'm gonna need a lot bigger tank! UGH!

I told my wife "It could be worse. We could be in a position where we couldn't afford the repair and need the repair"

Wish I had a set of those!

The fuel shut off valve on my log splitter engine started running fuel. Realizing I couldn't fix it, I bought another carb for 20$ shipped. Installed it and ran the splitter for about 45 minutes, and the engine started faltering. I looked and saw gas running out of the overflow port. The needle valve in the fuel bowl wasn't shutting the gas off, causing it to overflow out the port and also into the intake port. Couldn't adjust/fix it, so bought another carb on Amazon. I'm hoping I'm not just buying more junk, although I'm very suspicious.

I also had to fix my log slitter today. It was running like crap stalling every few seconds. Dropped the bowl and cleaned the carb 3 or 4 times. I think it must have had water in the gas. By the last few logs it finally cleared up.

Iv been working on this clock the last few days. The shroud needed alot of welding between flipping the logo and filling all the holes but it came out nicehttp://forums.pelicanparts.com/uploa...1579215698.JPG

Came from Amazon. Can you get stuff sent to you by Amazon?

Performance Tool W1716 Thumbwheel Ratchet Set, 3-Piece

Man that is way cool! SmileWavy

http://forums.pelicanparts.com/uploa...1579218347.jpg

This is my log splitter. It's a home made affair. The slide rail is a section of upside down railroad rail, and the rest is second hand hydraulics with everything welded together from scrap steel. I got it without an engine, cleaned everything up & out, and put a H.F. 13 hp. engine coupled to the hydraulic pump on it. The hydraulics are very old, and I bought a new pump. ram, and valve that I haven't installed because the old stuff still works great. Now if I could just find a carburetor that works.

Vegas carts makes a tunable carb for that HF engine.

Finally got around to pressure washing my circular driveway in the area where my '83 911SC and landscape trailer sat for so long.

I still have some rust stains to take care of and will with some industrial oxalic acid I bought.

I used the Ryobi hardscape cleaner attachment and my Sun Joe electric p/w and it worked really well. I used KrudKutter in my injection bottle as a pre-soak prior to doing the actual blasting.

http://forums.pelicanparts.com/uploa...1579395911.JPG

http://forums.pelicanparts.com/uploa...1579395911.JPG