what tile saw to get
 

I am too cheap to pay $20 per ft t install backsplash ($1000, need Porsche parts).
so its time to learn how to do tile.:mad:
I am putting in a mosaic backsplash, about 50sqf.
but the wife is already talking about new tile in both bathrooms, floors and showers.
there is also a chance of putting tile in the kitchen.

what size saw should I get.
found a used (pitbull) table top for $50, home depot also has a smll one for $135 but they also have one with a sliding table for $300. that's about as much as I want to spend. the sliding table seems like it would be easier for the mosaic stuff but I really don't have that many cuts to do. also seems easier than sliding along a fense.
I have 2 corners, 2 ends and a bunch of outlets. :mad: (now I regret putting in all those outlets for her).

I did see a nice used one with a stand and I sliding table for $250 but a little far away

I have a cheap Skil wetsaw. It did a great job on my massive tile project.
Im not sure about cutting mosaic though. Are those in sheets?

https://www.skil.com/120v-7inch-wet-tile-saw/

I bought one from a garage sale a while back (for $25 or so) that is equivalent to the model at HD for around $135. I've used it for a few small projects. If I were faced with several projects - including large tiles (flooring), I'd suggest the sliding table version as it will make cuts more accurate and easier.

We have 2 wet saws for the 'business', a sliding table, and a sliding blade.

However, I've done quite a bit at a vacation house with a harbor-freight angle grinder with diamond blade, and a sub $100 wet saw. In many ways, with the larger format tiles common today, the angle grinder and cheap wetsaw are easier. If you use the grinder, just mist the tile with water to keep down the dust.

What about renting a commercial-grade saw for a day?

So much nicer to use than a "happy homeowner" type saw, and no need to store it for the rare times it's used.

I had a cheaper version of that one, plasplugs or something like that. I also have a angle grinder with diamond blade that dad911 suggested. I have used both on mosaics, back-splash tiles, 4x4 all the way up to 18x18. Admittedly the 18" tiles were not that easy and I would have benefited from a large scale tile saw with sliding table.

Whatever you use make sure to put it on some sort of stand. I have two folding stands with a couple planks of plywood for work surface. Sure beats working on the ground. Wet saws will throw some water, especially the cheap ones. Pick some clothes for tile projects and plan on keeping them only for that purpose. The wife and I have our painter and landscaping clothes in the garage that we use weekly.

Share some pictures of your project!

A good blade is important and that it is a wetsaw.
I don't think it needs to be highend for a couple of jobs.

We have a IMER rail saw, but we don't too much stone or tile ourselves anymore. Bigger and more money is always better, but in your situation, I would just buy one of those 300 dollar home depot or Rigid saw and be down with it especially if you have a bath project coming your way. Its frustration to not have the right tool and I know most of us are perfectionists here. Rent one?

I've done more than my fair share of tilling but I've never had a dedicated tile saw...
Just a good scratch cutter and a diamond blade for the angle grinder.

I really enjoy the results. :D

http://forums.pelicanparts.com/uploa...1568653365.jpg

http://forums.pelicanparts.com/uploa...1568653437.jpg

I bought a commercial saw used a few years back.
Used it for cutting my pavers for my patio and sidewalk.
Will use it for some small tile projects at the house this fall.
Wasn't very expensive. I would have paid more for rental on the first section of patio.
I will probably sell it eventually for the same price I paid for it.

Good job there SC. I learned about lippage half way into a project.

I have a fireplace in the middle of a room in which has an in-door chimney up to a vaulted ceiling. I did a groutless ledgestone installation. Most of the tiles were not accurately assembled. I started with a chinese 7" wet saw but could not get accurate cuts with it. So I got a Bosch sliding table 10" saw. Very accurate cuts due to zero play in table. It's better than the DeWalt which is better than the chinese (Lowes, HD).

i saw those spacers in lowes today
do you use those for a floor that is uneven.

found a guy here in town that has some used ones and new ones, probably stolen.
going to look at some after work

Good skills Peter!!!

The spacers makes everything easier. It's a bit fiddly but the levels at the corners are perfect!

Honestly I wouldn't tile without them.

Here's a good video. There's lots of variants but they all work much the same.

<iframe width="560" height="315" src="https://www.youtube.com/embed/LcxTtcZEDdQ" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

Thanks Bill. My old legs ;)

http://forums.pelicanparts.com/uploa...1568663092.jpg

The HF one with the sliding table and a 10” diamond blade works great.
I think with a coupon I got it for 250 with a blade and tax

https://www.harborfreight.com/10-in-25-hp-tilebrick-saw-69275.html

Used it for pavers and tile. Unbelievable how much easier it was to get good repeatable cuts than the $100 7” skill thing I’d been using.

I did about 900sqft of ceramic tile (lots of cutting including around toilet flanges) with one like this from HD
https://www.homedepot.com/p/Rubi-24-in-Practic-Tile-Cutter-24985/202042337
https://images.homedepot-static.com/...85-64_1000.jpg

Then years later, we were going to be doing some granite tile, so I got something like this one below from HD. It did a great job of cutting through my granite, and then I loaned it to a friend that did his floor with granite tiles, and then later I did some more tile with it.

https://www.homedepot.com/p/QEP-3-4-HP-Wet-Tile-Saw-with-Back-Extension-22750Q/205620430

https://images.homedepot-static.com/...0q-64_1000.jpg

I’ve got an Imer rail saw and an MK sliding table saw. The MK is great for accuracy but won’t work on large format tiles. That’s where the rail saw comes in handy. Plus the MK is way heavy. The Imer not so much.

LOL, that's me. Under $10 for the HF diamond blade.

That, with a regular old tile scorer-breaker will just about cover everything I've needed to do so far.
But it might take longer and i usually end up with more "sample" pieces.

A few weeks ago I almost broke down and bought this for $65 but got by without it:

http://forums.pelicanparts.com/uploa...1568676904.jpg

How big is your Imer saw? We have a 10" and its super accurate with larger format tiles (trend today). We bought it because half way through a job, my tile got hit by a car on Sunday so we had to finish the job ourselves.