Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > Porsche 911 Technical Forum


Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered
 
Join Date: Oct 2005
Location: Merritt Island, Fl
Posts: 57
Installing Targa liner/padding

Help.
I have tried about six times. Each time for about 20 minutes to install the headliner under the targa bar. It seems I need ten hands and three sets of eyes.
Anyone have any hints on how I can get all the clips lined up and the head liner installed?

__________________
Black, Black, Black 1980 Targa.
Old 03-22-2008, 09:43 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #1 (permalink)
Registered
 
Join Date: Oct 2005
Location: Merritt Island, Fl
Posts: 57
cost to install a new interior

Anyone know a good shop that can do the interior of my targa here in central Florida or on the east coast of Florida?
I must admit that i am a better wrench turner and engine guy than a needle and thread guy. I loose my cool and get overwhelmed with putting this interior together.
Any ideas on cost for a complete interior assembly. I have all the parts.
__________________
Black, Black, Black 1980 Targa.
Old 03-23-2008, 06:13 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #2 (permalink)
Registered
 
Join Date: Oct 2005
Location: Merritt Island, Fl
Posts: 57
I hate to do this bump but I am in a situation that I need the car's interior done ASAP. Anyone have any suggestions?
__________________
Black, Black, Black 1980 Targa.
Old 03-26-2008, 10:44 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #3 (permalink)
abit off center
 
cgarr's Avatar
 
Join Date: Feb 2002
Location: At the Airport Kentwood, MI
Posts: 7,311
Garage
Send a message via Yahoo to cgarr
As I remember I bent down the clips, are they on the roll bar or the trim piece? Anyhow after getting it place I then pushed it up at each clip point to be bend the clips back tight. They may be too flat to get them all started.
__________________
______________________
Craig
G2Performance
Twinplug, head work, case savers, rockers arms, etc.
Old 03-26-2008, 11:26 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #4 (permalink)
Registered
 
BReyes's Avatar
 
Join Date: Feb 2005
Location: Orlando, FL, Treasure Coast, FL USA
Posts: 1,475
Garage
My interior guy is not fast. Period. Great guy he is. Jim is in St. Petersburg. Can expect closest thing to perfection too. pm me for his tel number and I will get it to you.

Have you called Donnie at Zots (Porsche service shop) in Orando as he may have a referral closer.

Regards,
__________________
Bernard
Old 03-26-2008, 11:41 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #5 (permalink)
Registered
 
Join Date: Oct 2005
Location: Merritt Island, Fl
Posts: 57
Thank!. My buddy uses ZOTs. I will ask him to call there for me.
I live in Merritt Island and hate to have to drive all the way across the state.
Thanks!

__________________
Black, Black, Black 1980 Targa.
Old 03-27-2008, 06:01 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #6 (permalink)
 
Reply


 


All times are GMT -8. The time now is 08:22 AM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.