|
|
|
|
| Author |
|
|
Registered
|
FS: Nose Panel & Rubber Spoiler
Rubber Spoiler in good condition with trim pieces and mounting hardware $50 +SH
 NA 85/1 Nose piece, has chips, straight. (vented headlight covers sold) $50 +SH 
__________________
Carl Race GTS!  Great Lakes Region, NASA PCA Member |
||
03-18-2012, 06:55 AM
|
|
|
Registered User
Join Date: Mar 2012
Location: near Spfg.,MO.
Posts: 8
|
How do you get the nose piece off? Do you have to drill or punch the spot welds? Mine might still be fixable. Sorry for the inconvenience. New to sight
|
||
|
03-18-2012, 11:54 AM
|
|
|
Registered
Join Date: Jun 2011
Posts: 515
|
I'll take those headlight buckets if they'll fit my '88na. Do you have the lights that go with them and all the mounting hardware?
|
||
|
03-19-2012, 06:04 AM
|
|
|
Registered
Join Date: Nov 2009
Location: Il
Posts: 113
|
Where are you located? Interested in nose piece.
|
||
|
03-20-2012, 07:11 PM
|
|
|
Registered
|
Nose panel is attached with screws over radiator bulkhead and by either screws or nut/bolt to fenders.
Headlight vents are sold, they did not house lights, were used for brake and air ducting. PM sent to 3rd poster. Thanks.
__________________
Carl Race GTS! Great Lakes Region, NASA PCA Member |
||
|
03-22-2012, 04:15 AM
|
|
|
Registered
|
Nose Panel SOLD! Thanks Pelican
__________________
Carl Race GTS! Great Lakes Region, NASA PCA Member |
||
|
03-25-2012, 07:56 AM
|
|
|
|
Registered User
Join Date: Mar 2012
Posts: 153
|
brake ducting
Any idea who made those headlight replacement pieces? We would like a set for the race car we are building
Thanks |
||
|
03-25-2012, 08:35 AM
|
|
|
Registered
|
It is pretty easy to do. Buy the dual inlet NACA vents (black, not clear). Dismantle the headlight covers so that you just have the metal cover (or buy used), from the inside of the cover, rough fit the vent to proper orientation, clamp it down and apply light heat from heatgun to warm vent (that's why black ABS) until it is formed to headlight cover. When satisfied, cool, outline vent with a marker, remove vent, retrace a cutout line about 1/2" to 3/4" inside other line, cut out and deburr, epoxy vent to cover, clamp. If you need it perfect, use body filler to mold around inlet of vent.
Cover was then simply attached at rear hung on a aluminum channel from inner fender to nosepanel. Bend a dzus plate to proper angle for front mount, test fit for proper appearance and adjust height, mount dzue plate to sheetmetal and drill hole in lower cover for dzus fastener, attach. You will probably need a pretty longthrow fastener, 3/4" (Paint that mount plate!!!!!) If you look close at dzuz plate, there is a bolt thru one of the holes, this was used to adjust the fit also (was not needed on right side)  [img]http://forums.pelicanparts.com/uploads20/156+5697_IMG1332691058.jpg [/img] 
__________________
Carl Race GTS! Great Lakes Region, NASA PCA Member |
||
|
03-25-2012, 09:12 AM
|
|
|
Registered
Join Date: Nov 2009
Location: Il
Posts: 113
|
Nose panel arrived today in good shape, very well packaged. Thanks.
|
||
|
03-27-2012, 07:20 PM
|
|
|
Registered
|
Thanks!
__________________
Carl Race GTS! Great Lakes Region, NASA PCA Member |
||
|
03-28-2012, 07:22 PM
|
|
