Pelican Parts Forums - Search Results

		Pelican Parts Forums > Search Forums
Search Results

Garage

Showing results 1 to 11 of 11
Search took 0.01 seconds. Search: Posts Made By: Tiger03447

Forum: Porsche 924/944/968 Technical Forum

10-05-2017, 08:03 PM

Replies: 110

Gas fumes? Tank leaks? Read this.

Views: 50,590

Posted By Tiger03447

During my resto project on my '83 944 I removed...

During my resto project on my '83 944 I removed the tank and sent it out to be powdercoated..BAD IDEA! The heat in the powdercoating oven desoldered many of the joints on the tank.Luckily, the...

Forum: Porsche 924/944/968 Technical Forum

04-16-2017, 07:40 PM

Replies: 14

How to remove front seat that doesn’t slide in any direction

Views: 3,949

Posted By Tiger03447

If you use the factory jack to move the seat, be...

If you use the factory jack to move the seat, be sure to use something other than the aluminum handle that came with the jack..It will break the handle at the crooked part. Just use a 9 or 10 inch...

Forum: Porsche Engine Conversion Tech Forum

03-21-2017, 04:06 AM

Replies: 112

Audi V8 in a 924.

Views: 36,314

Posted By Tiger03447

Will the bell housing bolt straight up to the 924...

Will the bell housing bolt straight up to the 924 Torque Tube? They look compatible...but what kind of bellhousing is on the back of the V-8? Is that the one off of the 924 engine?

Forum: Porsche 924/944/968 Technical Forum

01-06-2017, 07:02 PM

Replies: 3

Changing out rear wheel bearings

Views: 648

Posted By Tiger03447

Changing out rear wheel bearings

I have an early 944 with the stamped steel trailing arm suspension. The suspension is totally out of the car. Due to an inner seal being torn in half and dangling, along with the poor history of the...

Forum: Porsche 924/944/968 Technical Forum

09-21-2014, 11:25 AM

Replies: 17

Front fender adjustment

Views: 2,883

Posted By Tiger03447

Be advised that there is heavy sealant on the...

Be advised that there is heavy sealant on the inside of the fender where it meets the inner fender. You can disable this sealant with a heat gun and putty knife. I had to jam the knife up through the...

Forum: Porsche 924/944/968 Technical Forum

09-21-2014, 11:18 AM

Replies: 12

Hatch delamination - fill with silicone?

Views: 2,453

Posted By Tiger03447

Really neat! What a patriotic thing to do to the...

Really neat! What a patriotic thing to do to the sunroof!

Forum: Porsche 924/944/968 Technical Forum

09-21-2014, 10:39 AM

Replies: 3

Lifter installation

Views: 768

Posted By Tiger03447

On some engines it is advisable to soak the...

On some engines it is advisable to soak the lifters in oil for a day or so before installation to load them up with oil..Is this true on Porsche lifters too or should they be installed with just some...

Forum: Porsche 924/944/968 Technical Forum

09-21-2014, 10:12 AM

Replies: 15

Distributor Rotor removal

Views: 2,206

Posted By Tiger03447

Your fluid on the floor and the lack of a clutch...

Your fluid on the floor and the lack of a clutch are probably indicators that the slave cylinder just blew apart..or that the line between the clutch master and the slave failed..would recommend...

Forum: Porsche 924/944/968 Technical Forum

09-18-2014, 08:41 PM

Replies: 9

1987 944s Fuel Injectors

Views: 1,900

Posted By Tiger03447

Tiger03447

I pulled all four of mine for checkout for my '83 944. All were bad so what to do? I checked the stats at AutoZone and found that a GM injector would work OK. Still haven't checked it out since the...

Forum: Porsche 924/944/968 Technical Forum

09-18-2014, 08:25 PM

Replies: 19

Oil temp gauge

Views: 2,785

Posted By Tiger03447

Sunpro/Actron makes both electrical and direct...

Sunpro/Actron makes both electrical and direct reading temp gauges. they will work either for water or oil. If you have the later pan, you could perhaps use the oil quantity port for a direct reading...

Forum: Porsche 924/944/968 Technical Forum

09-18-2014, 07:57 PM

Replies: 1

Tiger03447

Views: 350

Posted By Tiger03447

Tiger03447

I am trying to install a motorized Recaro seat out of a 1988 944 parts car into my non-motorized 1983 944. I have pulled the driver's seat out of the car and have unplugged the electrical cables...

Showing results 1 to 11 of 11

Forum Jump

All times are GMT -8. The time now is 02:27 AM.