Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Search Forums
Reload this Page Search Results
Register Garage FAQ Community Calendar Today's Posts Search


Page 1 of 2 1 2 Next »
Showing results 1 to 25 of 42
Search took 0.01 seconds. Search: Posts Made By: rmolina
Forum: Porsche 914 & 914-6 Technical Forum 08-23-1999, 06:27 PM
Replies: 0
Views: 560
Posted By rmolina
brake woes....

ok ive got the new master cylinder in, newly rebuilt rear calipers and managed to get s.steal brake lines on the front, but the rear flex lines are almost imposible, I got one good twist in before...
Forum: Porsche 914 & 914-6 Technical Forum 06-08-1999, 01:04 AM
Replies: 2
Views: 579
Posted By rmolina
starter intermittent, help

ive had this happen to me 3 times, all under diferent circumstances, once when cold wet weather, once in warm, and once after sitting 6 hours, the problem is I hear the starter spining but it seems...
Forum: Porsche 914 & 914-6 Technical Forum 05-31-1999, 09:14 PM
Replies: 5
Views: 866
Posted By rmolina
Im at 24 in from floor to outside wheel well,...

Im at 24 in from floor to outside wheel well, when mesuring through the center hub. The car looks and handles much better, very minor kick when going over bumbs. I think its a keeper ...
Forum: Porsche 914 & 914-6 Technical Forum 05-29-1999, 10:00 PM
Replies: 5
Views: 866
Posted By rmolina
Thanks Ill try it, Im sure that the rear is...

Thanks Ill try it, Im sure that the rear is sagging,so I know its time to replace all the 30 yr old stock shocks/springs and trosion bars, but then I mind as well do all the bushings and ball...
Forum: Porsche 914 & 914-6 Technical Forum 05-29-1999, 06:45 PM
Replies: 5
Views: 866
Posted By rmolina
adjusting the front height

I need to drop the front an inch & 1/2 or so, I unloaded the weight in the front trunk and know Im riding high. for the torsion bar adjustment screws, I turn them counterclock wize right, Ive been...
Forum: Porsche 914 & 914-6 Technical Forum 05-25-1999, 09:55 PM
Replies: 4
Views: 838
Posted By rmolina
I have had my share of trany shifting problems,...

I have had my share of trany shifting problems, Ive got a tail shifter, I found like the others that replaceing the nylon bushings are just the begining, after replacing all the bushings and the cup,...
Forum: Porsche 914 & 914-6 Technical Forum 05-24-1999, 10:48 PM
Replies: 6
Views: 2,771
Posted By rmolina
thanks, im going to only replace the belt, so i...

thanks, im going to only replace the belt, so i need info on the sheet metal, which ones to remove, also since i need to buy the right hex socket it would help to know the exact size of the hex nut,...
Forum: Porsche 914 & 914-6 Technical Forum 05-24-1999, 11:07 AM
Replies: 6
Views: 2,771
Posted By rmolina
alternator belt replacement...warm air guide removal...

Every weekend it seems I replace or repair something, oh well it keeps me out of trouble (wink wink nudge nudge) this week end I'm going to replace the 8 year old alternator belt,

Ive read D....
Forum: Porsche 914 & 914-6 Technical Forum 05-23-1999, 12:58 PM
Replies: 8
Views: 725
Posted By rmolina
ya after replacing the cover plate with a new...

ya after replacing the cover plate with a new gasket, I still had the leak, S.Shroed was correct it was the o-ring a 0.12$ part that cost me 20$ to correct in wrong parts..

Thanks for the help, I...
Forum: Porsche 914 & 914-6 Technical Forum 05-23-1999, 12:55 PM
Replies: 1
Views: 659
Posted By rmolina
easy problem solved, end this thread.... thanks

easy problem solved, end this thread.... thanks
Forum: Porsche 914 & 914-6 Technical Forum 05-22-1999, 10:54 PM
Replies: 1
Views: 659
Posted By rmolina
speedo cable o-ring replacement

I traced the leak in my trany to the speedo cable, acording to an illistration in the haynes manual, it looks like this cable and its gear is held in by a lock bolt, is this the only bolt I have to...
Forum: Porsche 914 & 914-6 Technical Forum 05-21-1999, 08:21 PM
Replies: 1
Views: 656
Posted By rmolina
trany oil suggestions.. synthetic or dino?

Im going to fix the rear leak in my trany this weekend but was wondering about oil.. any suggestions? SAE 90, red line 70-90?
Forum: Porsche 914 & 914-6 Technical Forum 05-16-1999, 10:15 PM
Replies: 3
Views: 669
Posted By rmolina
related to my smoking vent .. someone explain the 3 levers heating settings

Im having electrical smoke come out of my vent in front of my windshield, assuming this is from a short in the fresh air fan, what settings do I use to make sure this fan does not activate? in short...
Forum: Porsche 914 & 914-6 Technical Forum 05-16-1999, 07:54 PM
Replies: 1
Views: 570
Posted By rmolina
electrical smoke from the vent infront of the windshield..whats there?

this has happened 2 times, I smell the obvous electrical burnning then I see smoke comming out of the outside vent infront of the windshield... thats there, how do I access it? when I open the hood I...
Forum: Porsche 914 & 914-6 Technical Forum 05-15-1999, 06:26 PM
Replies: 1
Views: 634
Posted By rmolina
modern gas + 30yr old fuel lines = pain in the a$$......

Well, I was leaving work and I noticed a rather large puddle underneith and behind my pasenger door. guess what it was? You are correct sir, FUEL! This was great since I had just filled the tank the...
Forum: Porsche 914 & 914-6 Technical Forum 05-09-1999, 09:04 PM
Replies: 2
Views: 629
Posted By rmolina
head temp and oil pressure references, am I reuuning hot w/low pressure?

Ive just installed my guages, I was wondering what some of you have for oil pressure and head temp? Id like to get 3+ responses so I can average. also are you using a high vol. oil pump or relief...
Forum: Porsche 914 & 914-6 Technical Forum 05-08-1999, 09:28 AM
Replies: 8
Views: 725
Posted By rmolina
thanks for the safety tips ...

thanks for the safety tips http://www.pelicanparts.com/ultimate/smile.gif
wish me luck thats its only the cover plate gasket...
Forum: Porsche 914 & 914-6 Technical Forum 05-08-1999, 09:25 AM
Replies: 5
Views: 603
Posted By rmolina
Thanks for the replys, Im painting the car soon...

Thanks for the replys, Im painting the car soon anyway so Ill just fill the holes.
Forum: Porsche 914 & 914-6 Technical Forum 05-07-1999, 11:17 AM
Replies: 5
Views: 603
Posted By rmolina
1.7 logo: possibly the stupidest question

Possibly the stupidest question: Ive looked at dozens of 914 pics and for the life of me find a 914 with the 1.7 logo on the back. I have the 914 logo, but no 1.7, there are holes on the left side of...
Forum: Porsche 914 & 914-6 Technical Forum 05-07-1999, 10:36 AM
Replies: 8
Views: 725
Posted By rmolina
oil leak, @ the shift lever cover plate?

On my 71 tail shifter, the only oil leak I have, thank god, is comming from the rear of the trany, A couple of drops daily. It accumulates on the bolts/nut of the shift lever cover plate, my weekend...
Forum: Porsche 914 Used Parts For Sale & Wanted 05-06-1999, 11:22 PM
Replies: 8
Views: 611
Posted By rmolina
im looking fot 73-74 oront and rear bumper horns,...

im looking fot 73-74 oront and rear bumper horns, as aell as a center console
Forum: Porsche 914 & 914-6 Technical Forum 05-06-1999, 09:02 PM
Replies: 0
Views: 597
Posted By rmolina
whens the next pomona show?

whens the next pomona show?
Forum: Porsche 914 & 914-6 Technical Forum 05-05-1999, 09:49 AM
Replies: 2
Views: 669
Posted By rmolina
building a center console...

Im going to build a center console, Ive seen pics and have a pretty good idea of how I want it, but would like mesurements. I have a wood dash and would like to contuine the theme into the center...
Forum: Porsche 914 & 914-6 Technical Forum 05-04-1999, 09:29 AM
Replies: 2
Views: 586
Posted By rmolina
Thanks, it was an 11mm, nice I dont grind rev...

Thanks, it was an 11mm, nice I dont grind rev anymore http://www.pelicanparts.com/ultimate/smile.gif
Forum: Porsche 914 & 914-6 Technical Forum 05-03-1999, 11:22 PM
Replies: 2
Views: 586
Posted By rmolina
tightening up my clutch, at the pedal end or the trany end?

I have to press the clutch to the floor, Id like to tighten it up a bit, Which end is easier? the pedal or the trany end? easy to do, just a lock nut on the cable? please explain, thanks all...
Showing results 1 to 25 of 42
Page 1 of 2 1 2 Next »

 
Forum Jump

All times are GMT -8. The time now is 06:42 PM.

Contact Us - Pelican Parts Catalog for Porsche, BMW, Mercedes-Benz, MINI and More - Archive - Privacy Statement - Terms of Service - Top

 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.