|
|
|
|
| Author |
|
|
Registered
Join Date: Jul 2002
Location: TN
Posts: 2,507
|
What to use for 8.1 commpresson on turbo Motor
I am in the process of rebuild the motor (top end)
it is currently 1984 3.2 turbo @9.5:1 what are my options to achieve 8.1:1 compression Thank You
__________________
Williamknightperformance.com Perfectpower.com |
||
02-23-2005, 06:03 AM
|
|
|
Still Doin Time
Join Date: Nov 2004
Location: Nokesville, Va.
Posts: 8,225
|
If you have good ring seal you could install a different set of cams that would A) Be compatible with a street turbo set-up and B) Bleed off some of your existing cylinder pressure which will have the same effect as reducing the mechanical compression ratio.
PM John (Camgrinder) for advise
__________________
'15 Dodge - 'Dango R/T Hauls groceries and Kinda Hauls *ss '07 Jeep SRT-8 - Hauls groceries and Hauls *ss Sold '85 Guards Red Targa - Almost finished after 17 years '95 Road King w/117ci - No time to ride, see above '77 Sportster Pro-Street Drag Bike w/93ci - Sold |
||
|
02-23-2005, 07:01 AM
|
|
|
Registered
Join Date: Jul 2002
Location: TN
Posts: 2,507
|
How about Mahle 98mm turbo pistons?
__________________
Williamknightperformance.com Perfectpower.com |
||
|
02-23-2005, 08:38 AM
|
|
|
Somewhere in the Midwest
Join Date: Oct 2001
Location: In the barn!
Posts: 12,499
|
Tony,
I am having my cylinders bored and Nikasil plated to match 98 mm JE pistons. I'm not going to go as low in CR as you will, but I believe the JE pistons can be ordered with the CR you want. I'm building a 3.4 Turbo. |
||
|
02-23-2005, 08:43 AM
|
|
|
Registered
Join Date: Jul 2002
Location: TN
Posts: 2,507
|
I wanted to do what wydryd was interested in
Boring from 955mm to 98mm
__________________
Williamknightperformance.com Perfectpower.com |
||
|
02-23-2005, 09:12 AM
|
|
|
Somewhere in the Midwest
Join Date: Oct 2001
Location: In the barn!
Posts: 12,499
|
If you mean by boring and replating..that's what I'm doing.
|
||
|
02-23-2005, 09:33 AM
|
|
|
|
Forced Induction Junkie
|
Does anyone have a pic of a JE 98mm piston dome? I was wondering if they do custom compressions AND custom domes for those of us that have twin-plugged our engines.
__________________
Dave '85 930 Factory Special Wishes Flachbau Werk I Zuffenhausen 3.3l/330BHP Engine with Sonderwunsch Cams, FabSpeed Headers, Kokeln IC, Twin Plugged Electromotive Crankfire, Tial Wastegate(0.8 Bar), K27 Hybrid Turbo, Ruf Twin-tip Muffler, Fikse FM-5's 8&10x17, 8:41 R&P |
||
|
02-23-2005, 11:36 AM
|
|
|
Wo ist die Rennstrecke?
Join Date: Mar 2004
Location: St Johns, FL
Posts: 1,210
|
I had JE make custom pistons for me. You can see a pic at:
http://www.brookstonefarms.com/930rebuild_page2.htm I am building a motor that has a stroked (964) crank, super 964 cams, custom 98mm pistons and 3.2L cylinders bored out to 98mm (better cooling than the 3.3 cylinders and A LOT cheaper than Mahle). The compression is 8.0:1 with very little dome on the pistons. |
||
|
02-23-2005, 03:47 PM
|
|
|
Forced Induction Junkie
|
Thanks, Don
__________________
Dave '85 930 Factory Special Wishes Flachbau Werk I Zuffenhausen 3.3l/330BHP Engine with Sonderwunsch Cams, FabSpeed Headers, Kokeln IC, Twin Plugged Electromotive Crankfire, Tial Wastegate(0.8 Bar), K27 Hybrid Turbo, Ruf Twin-tip Muffler, Fikse FM-5's 8&10x17, 8:41 R&P |
||
|
02-23-2005, 04:36 PM
|
|
1985 Porsche 930 Fac. Slantnose 3.3l
