Fill for laneway
 

Seeing we all know about pulling stumps ...... what would you use to fill holes in my laneway? It appears to be gravel. The holes hold water and then get muddy.
It sucks that a day after it rains there is still mud and I have to drive my Porsches through it.
Gravel? Limestone? Crushed asphalt? http://forums.pelicanparts.com/uploa...1603989428.jpg
http://forums.pelicanparts.com/uploa...1603989570.jpg
http://forums.pelicanparts.com/uploa...1603989570.jpg
http://forums.pelicanparts.com/uploa...1603989570.jpg
http://forums.pelicanparts.com/uploa...1603989570.jpg

AB.

aggregate Base

Crushed limestone - #411 (AKA Chips and Dust).

My driveway is 1/2 mile in length, plus spurs to the barns, etc.

When we moved here the road was a mess: Bank and run and rougher that the Baja 500. After a heavy rain it was like driving in Guatemala.

Slight hyperbole:)

I went with 3/4 inch stones because they very cheap here. When there was a local gravel pit they charged me $5.00 dollars a ton.

I have it to the point where maintenance is very easy and the road can be snow plowed. Since I snow plow, I do keep the blade up a tad.

The road sees a lot and holds up remarkably well.

http://forums.pelicanparts.com/uploa...1603991987.JPG

http://forums.pelicanparts.com/uploa...1603991987.JPG

http://forums.pelicanparts.com/uploa...1603991987.jpg

I remember that driveway!

Still a great looking farm Paul.

3 choices. lol
I am just filling holes, not making a new laneway.
Here is what my local place can deliver. Or I'll just get a few bags.

https://www.ggconline.ca/we-deliver/

Thirty feet or 1/2 mile, doesn't matter. I'd start with the gravel then cover with the 3/8 clear stone.

Get more than you think you'll need. There is a lot of repair to be made, at least as I see it.

crusher run!!!
I have different stuff on different parts of my driveway.
3/4", 1/2", and crusher run.
Weeds grow up through everything but the crusher run.
Gravel moves around a bit, even after it settles, forming more puddles.
Crusher run packs down like concrete. No weeds and no puddles.

The existing surface looks to be round pea gravel. It will sink into mud, move around, and get kicked up by tires and chip car paint.

I think using crushed limestone alone needs to be compacted, doesn't have a hard wear surface, and being on the soft side may eventually shift like sand.

Aggregate base (aka 3/4") is large and irregular-shaped. It settles and locks into place eventually. Rolling it will provide the best result. Building it up higher will provide consistent drainage. It looks like several types of stone material is used for it.
--------
I used to have a 3/4" crushed concrete drive..which was sharp and hell on bare feet and dog paws..but provided superior traction for a slippery hill during the winter.

It was not compacted.

I finally asphalted it because the snowblower turned into a machine gun pelting neighboring houses and cars.
Grass also grew fast in that particular formula. Probably no base.

I have baaad news - it looks like there is an inadequate base

that means you need to excavate, and not just the hole either

the good news: there is likely no need to go deeper than 3-4 ft.

crusher run.

Clean out the dirt/mud, throw some filter fabric on the bottom.

Funny you say that. A friend is a landscaper and quoted me $6,000 to do just that.

Be much much cheaper just to pave it, but it's a snowmobile access to the lake and the cardbides would do a number on it.

Why is it holding up fine for my neighbour to the left?

Low spot, turn in/around, soft foot, poor drainage?
Get some 25mm crush gravel. Level and compact. Keep a pile to keep dressing it as it sinks. It has to stop sinking sometime!

Here, recycled crushed concrete is almost free... Compacted well it pretty much turns back into solid concrete.

do you know the soil conditions for him? or the underlayment?

I just made a guess based on "Keswick/Ontario" and your pics - hope I guessed wrong...

you may be on lake sediments; there could a slight ridge of rock he's on, etc.

I think the pictures are a little deceiving. The laneway is very compacted and hard. I tried hitting it with a spade and it could barely scratch the surface. The holes are maybe 1/4" deep, but water will sit in them and then the water will collect dirt/leaves that is blowing around in the air and turn to mud.
I think this happened because the little sh#t renters next door use it to do doughnuts on their mini atv's. The same ones that used my dining room table as a dock before the waves destroyed it.

3/4 plant mix. Crushed granite is what we use on the town roads here.
Since we (the town) switched to crushed granite we hardly have a mud season any more.
My driveway used to always get muddy in the spring.......not any more.

well, you could just fill it

or excavate xx feet wide across the lane, then fill that

what are the stds. for a low use road there? like in town, a residential street or collector? - that should be more than you need to do

What about this stuff? I'm just filling the potholes so they don't pool.
http://forums.pelicanparts.com/uploa...1604000950.jpg

That’s fine, we’re just telling you to order a dump truck load of it, get a box blade and address the whole driveway.

Is a laneway similar to a henway only heavier?

Why do we park on driveways and drive on parkways?