![]() |
I remember the rope tows. No one can match this... My first skiing was a Pinecrest Lake. Anyone ever ski there? I became the expert on the rope tows after practice at Dodge Ridge. I also enjoyed the T bars and poma lifts with the wire that rolled up. If you let go at the wrong time the guy yelled at you because the wire got caught up in the big wheel at the end. I remember finally getting the nerve to go on the chair lift. Of course we were on lace boots and cable bindings. Lift tickets I think were $4 and there was talk this was a bit high.
|
As a freshman at CU in 1983, I went skiing a lot. I remember that attitude towards snowboarding.
|
Quote:
|
^^^ Caberfae, Crystal Mt, and sometimes Boyne here.
Boyne Mt and Highlands were always a treat. |
Quote:
|
I was 16, Kratka Ridge CA. Off of the helipad. Never boarded, never will.
http://forums.pelicanparts.com/uploa...1645668452.jpg |
1974 Mammoth Mtn. Chair Lift operator for Fritz, $3.00 per hr. , free lunch in cafeteria, free skiing on Monday. The steam vents on the mountain were active then, 90mm cannon for avalanche control
|
Started skiing @ badger pass in 1976..... Back when crashing had serious consequences... like getting hit in the melon with a ski tethered to your ankle... I live in Northern ut now within 20 minutes of 3 ski mountains, I taught at 2 of them. I've had the privilege to teach 9 of 12 grandchildren, most started once they could walk. I get to rip 2-6 days a week, good times...
Snowboarding revolutionized ski manufacturering and I'm thankful for it... The minute Jake realized he needed metal edges and a large side cut, we reaped the benefit. Now my best days are pow, but because of fat side cut I get to carve trenches in cords. It's sweet to have fun in pow and pack. I've been hit and hurt by as many skiers as single plank wanks.... Bottom line, I'm thankful for the advances spun to us as a result of boards. About the only thing I don't like is destroyed moguls and retarded turns that destroy a pristine pitch of pow.... Save the buffalo man |
Quote:
|
At badger the ropes got wet (Sierra cement) you'd hold the rope and squeeze tight then as soon as the gloves almost smoked it would grip.... And jerk me onto my face... And stretch my arms 2 inches out of socket.
|
Quote:
Character building, skiing in the midwest was... |
Quote:
(actually it's pretty safe as most injuries come from the "phantom foot" and other things related to having a fixed heel in alpine bindings - freeheel usually translates into faceplant and not knee reconstruction) |
Came up as a skater in Craig Kelly’s hometown, a few years younger. There was no question
|
I remember my older brother having downhill skis with boot bindings that had a large coil spring that was supposed to keep the boot in. What were they called?
|
Quote:
|
Lifting a heel up...with the ski not following, must have been challenging.
The new bindings are very nice. |
There were clips on the side of the ski to grip the cable and hold the heel down.
Basically they were mountaineering bindings. Lots and lots of binding innovation in the 60 and 70's. At various stages in my evolution I had cable bindings, Miller, Look Nevada, Spademan, and I eventually settled on the various generations of Salomon 7x7. I remember the ski brake as one of the best inventions of my ski life. Trying to unwrap a leash and then setting the heel of the Look Nevada to line up with your boot after a fall and release in deep powder on a steep hill could be a pretty frustrating and time consuming experience. Later, I just learned to not fall. |
Fun fact, a company in Austria called Geze made cable ski bindings and Porsche used the Geze spring loaded lever from these bindings as the engine compartment latch on the 906 race car.
|
Here's my current pair....old, but I still like them a lot.
http://forums.pelicanparts.com/uploa...1645734356.jpg |
Me on the left circa 1968. This was my very first ski trip to what used to be Great Gorge NJ. Note the high tech gear. :D That jacket was my Dads old Eisenhower jacket.
http://forums.pelicanparts.com/uploa...1645734458.jpg |
All times are GMT -8. The time now is 07:36 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website