|
|
|
|
| Author |
|
|
Registered
Join Date: Apr 2007
Location: Bellingham, WA
Posts: 249
|
spring for MFI throttle body
I am looking for the part number for the spring that helps close the throttle plates. there are 6 used. I checked ETCA, but the exploded parts diagram did not break them out. I could see them drawn on the throttle body
TIA Tom
__________________
68 Beetle 68 to 72 sold 72 911T Nov 71 to present P/U @ factory Nov 19. Car was gift to myself for surviving the army 67 VW split window 74 to 76 sold 81 VW caddy 81 to present |
||
04-05-2019, 08:17 AM
|
|
|
Functionista
Join Date: Jul 2011
Location: CO
Posts: 7,717
|
90111013102, leg spring. About $15 each
__________________
Jeff 74 911, #3 I do not disbelieve in anything. I start from the premise that everything is true until proved false. Everything is possible. |
||
|
04-05-2019, 10:58 AM
|
|
|
(man/dude)
|
I think 90111013102 might be the single spring for the crossbar, not the x6 ones for the individual throttles.
__________________
Heavy Metal! Part Deux - The Carbon Copy Project Heavy Metal https://tinyurl.com/57zwayzw (SOLD) 85 Coupe - The Rot Rod! AX beater Quality Carbon Fiber Parts for Classic 911s: instagram.com/jonny_rotten_911 |
||
|
04-05-2019, 02:57 PM
|
|
|
Functionista
Join Date: Jul 2011
Location: CO
Posts: 7,717
|
Except in PET it shows quantity required is (6) so I think that’s it..
__________________
Jeff 74 911, #3 I do not disbelieve in anything. I start from the premise that everything is true until proved false. Everything is possible. |
||
|
04-05-2019, 04:02 PM
|
|
|
(man/dude)
|
Quote:
I won't be over to the shop till later but if I think of it I'll look at both of them and see if I can figure it out.
__________________
Heavy Metal! Part Deux - The Carbon Copy Project Heavy Metal https://tinyurl.com/57zwayzw (SOLD) 85 Coupe - The Rot Rod! AX beater Quality Carbon Fiber Parts for Classic 911s: instagram.com/jonny_rotten_911 |
||
|
04-06-2019, 06:55 AM
|
|
|
Registered
Join Date: Jun 2003
Location: Camarillo, Ca.
Posts: 2,418
|
That number is for the crossbar. Porsche does not offer individual parts for the throttle bodies. I service throttle bodies so let me know if you require service.
__________________
Aaron.  F.S. 1965 Solex engine w carbs/cleanerBurnham Performance https://www.instagram.com/burnhamperformance/ Last edited by BURN-BROS; 04-06-2019 at 07:28 AM.. |
||
|
04-06-2019, 07:16 AM
|
|
|
|
Registered
Join Date: Apr 2007
Location: Bellingham, WA
Posts: 249
|
does anyone know the specs for the spring? wire diameter etc
__________________
68 Beetle 68 to 72 sold 72 911T Nov 71 to present P/U @ factory Nov 19. Car was gift to myself for surviving the army 67 VW split window 74 to 76 sold 81 VW caddy 81 to present |
||
|
04-06-2019, 08:09 AM
|
|
|
Registered
Join Date: Feb 2008
Posts: 1,438
|
It would not be hard to make some springs, there are only six. I've made them in the past. All you need is one spring to use as a master, a little trial & error development can resolve your issue. If your shafts are loose then check out Aaron Burnham for service, Post #5.
__________________
Paul Abbott Weber service specialist www.PerformanceOriented.com |
||
|
04-06-2019, 08:37 AM
|
|
|
Registered
Join Date: Apr 2007
Location: Bellingham, WA
Posts: 249
|
I am fighting a slow to get back to idle after slowing down. so far I have cleaned & greased all of ball/sockets & replace the bushings for the lever arms.
The springs are very rusty, so I thought I would replace them
__________________
68 Beetle 68 to 72 sold 72 911T Nov 71 to present P/U @ factory Nov 19. Car was gift to myself for surviving the army 67 VW split window 74 to 76 sold 81 VW caddy 81 to present |
||
|
04-07-2019, 11:00 AM
|
|
