Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > Porsche 911 Technical Forum


Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered
 
North Coast Cab's Avatar
 
Join Date: Sep 2002
Location: Cleveland
Posts: 4,424
Garage
Question What Clucth Should I Put In?

Winter project this year will consist of the first engine drop, some routine maintenance and a new clucth. What type of clutch should I install?

I use it for a few autocrosses per year and I just purchased a roll bar so I can do some DE's.

I see the oem kit, the Sachs power clutch kit, and the Center Force kit. I'm sure there are others.

What should I install, or is there a preferred mix and match option to attain the best set-up for my driving?

I intend to to replace everything, cable, bearing, fork etc.

JG

P.S. I know it's not winter but I'm stockpiling parts early to reduce winter sticker shock.

__________________
1985.5 944 GTS
Old 08-24-2003, 10:48 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #1 (permalink)
Registered
 
North Coast Cab's Avatar
 
Join Date: Sep 2002
Location: Cleveland
Posts: 4,424
Garage
Bump.
Someone must have some input.
The Sachs US headquarters is only 2 miles from my house. I may start rummaging through their garbage shorly.

JG
__________________
1985.5 944 GTS
Old 09-01-2003, 12:45 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #2 (permalink)
Navin Johnson
 
TimT's Avatar
 
Join Date: Mar 2002
Location: Wantagh, NY
Posts: 8,786
See if you can get an RSR clutch, all aluminum, more clamping power, slightly more leg effort ( heard these are NLA). If not the Sachs PowerKit would be fine.
__________________
Don't feed the trolls. Don't quote the trolls
http://www.southshoreperformanceny.com
'69 911 GT-5
'75 914 GT-3
and others
Old 09-01-2003, 01:06 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #3 (permalink)
Registered
 
Carrera Sled's Avatar
 
Join Date: Aug 2003
Location: Louisville, KY
Posts: 98
I just put a stock Sachs kit in my '85, but not long ago so I can't tell you what kind of life to expect. I've never noticed any slippage under any hard acceleration. (Stock engine). I actually went into the clutch because the throwout bearing failed, along with a few broken fingers on the pressure plate diaphragm spring; it actually pulled it right out of the pressure plate. I was surprised to see that the disc looked like it had about 100 miles or so (<.005") left before it wore down to the rivets! I guess these don't give any warning (i.e. slippage) before they tear into the flywheel & pressure plate! This is my first 911 and clutch work on one.
__________________
'85 Carrera Coupe, White Gold Metallic - 8" rear Fuchs, Fittipaldi steering wheel, Weltmeister short shift, Turbo tie rods.
"If you can make black marks on a straight from the time you turn out of a corner until the braking point of the next turn, then you have enough horsepower." - Mark Donohue
Old 09-01-2003, 01:13 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #4 (permalink)
Registered
 
Join Date: Mar 1999
Location: Cornwall-on-Hudson, New York, USA
Posts: 4,499
If you're gonna go to the trouble, put in the lightest, best clutch (and flywheel, why not) that you can. I'm running a Truman aluminum flywheel and a Sachs (as I remember...) aluminum clutch. People will tell you that with such a setup you wont' be able to get the car off the line without stalling, but I find my wife's Boxster to be more clutch-sensitive than my '83 SC with a finicky, carbureted engine and aluminum clutch.

Stephan
__________________
Stephan Wilkinson
'83 911SC Gold-Plated Porsche
'04 replacement Boxster
Old 09-01-2003, 03:06 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #5 (permalink)
Moderator
 
Bill Verburg's Avatar
 
Join Date: Dec 2000
Posts: 26,411
Garage
The Sachs Power clutch kit is a lot of bang for the buck. It will feel like stock but grip better. The weight is a non issue, aluminum or steel won't matter much. It's the 964/993 w/ 50# clutch/flywheels going down to 12 or so # that will have an issue.

Some of the carbon segmented clutches don't take kindly to slipping, they can be more like an on/off switch
__________________
Bill Verburg
'76 Carrera 3.6RS(nee C3/hotrod), '95 993RS/CS(clone)
| Pelican Home |Rennlist Wheels |Rennlist Brakes |
Old 09-01-2003, 03:13 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #6 (permalink)
 
Registered
 
350HP930's Avatar
 
Join Date: Jun 2003
Location: St Petersburg, FL
Posts: 3,814
A few years ago I replaced my pressure plate with the OEM sachs unit and my old disk with the earlier sachs 930 disk that had the spring center section instead of the late model rubber one.

When I dropped my motor a few months ago everything still looked as good as new after almost 40K miles of use with the exception of a lot of dust, but I go pretty easy on my clutches.

Old 09-01-2003, 03:40 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #7 (permalink)
Reply


 


All times are GMT -8. The time now is 05:08 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.