Parts Needed \ WTB

[Christien]

I'm looking for a complete interior in tan for an 87 911 cabrio. I need everything except carpet, including dash, console and shifter boot.

[Bergo]

Anyone have a set of headers (no heat) available? OBX has some on eBay, but US shipping kinda kills. No sense paying as much for shipping as for the headers themselves.

[Mark Henry]

Originally Posted by Bergo

Anyone have a set of headers (no heat) available? OBX has some on eBay, but US shipping kinda kills. No sense paying as much for shipping as for the headers themselves.

I bet I can squat and pop out a nice steaming turd that's a better fitting and tuned than a OBX header.

...and I didn't rip anyone off to get the design.

[rywats]

Hi guys,

I'm looking for a pre 74 grill for my engine lid.

Thanks in advance!

[haycait911]

Originally Posted by rywats

Hi guys,

I'm looking for a pre 74 grill for my engine lid.

Thanks in advance!

I've got some. pm me.

[haycait911]

Originally Posted by Bergo

Anyone have a set of headers (no heat) available? OBX has some on eBay, but US shipping kinda kills. No sense paying as much for shipping as for the headers themselves.

I have a pair of Georges, and some Bursch. pm me.

[Hawkeye's-911T]

Looking for right front control arm (A-arm) for a 1970 T.
Thanks in advance.

Cheers
JB

[pors1968]

Originally Posted by Hawkeye's-911T

Looking for right front control arm (A-arm) for a 1970 T.
Thanks in advance.

Cheers
JB

With front sway bare or no sway bare.

[JJ 911SC]

Originally Posted by haycait911

I have a pair of George...

Is that from Walmart?

[Hawkeye's-911T]

Hi pors1968

Although there was no sway bar installed in the car, the control arms had provision for one. I am leaning toward doing that upgrade in the future when the budget allows for same. As you can see by the photo, this one suffered some impact damage - enough to cause me some worry. The bent (hypotenuse) portion has a small crease on the underside so I feel its strength may be compromised even after I straightened it out. Thanks for your response.

Cheers
JB

[pors1968]

Send me a pm for your e-mail ill send pict.RICHARD

[boxcarracer]

Not urgent, but does anyone have a steering rack for an '86 911?

[Mark Henry]

Originally Posted by Hawkeye's-911T

Hi pors1968

Although there was no sway bar installed in the car, the control arms had provision for one. I am leaning toward doing that upgrade in the future when the budget allows for same. As you can see by the photo, this one suffered some impact damage - enough to cause me some worry. The bent (hypotenuse) portion has a small crease on the underside so I feel its strength may be compromised even after I straightened it out. Thanks for your response.

Cheers
JB

The sway bar mount can be cut off and welded on the new arm.
I think that year is the same arm as a 914, just a thicker torsion bar that you have in your old arm.

[Jim2]

Originally Posted by boxcarracer

Not urgent, but does anyone have a steering rack for an '86 911?

Ive got a few but one is from an 86. Catch me in a couple days once I'm back, if you haven't located a closer one.

[Hawkeye's-911T]

Hi Richard
PM sent
Cheers
JB

[pors1968]

Originally Posted by boxcarracer

Not urgent, but does anyone have a steering rack for an '86 911?

I think i have couple SC should be the same.

[kennethg]

Looking for a 2.7L engine for a 2005 Boxster. Any leads would be appreciated.

Ken

[TargaT]

Hi, looking for lower turbo valve covers. Euro bumperettes (rear) for a mid year, also/or mid year bumper (rear)

Thanks, Joe

[911T70]

I'm looking for the U-bracket that guides the clutch cable. It bolts onto the transmission, #81 on the diagram below. Anyone have one for sale?

[rywats]

Wanted: front aftermarket valence or oem SC front lip spoiler!!