Parts Needed \ WTB

[tholyoak]

I have one, going to depend on where you are though.

-Todd

Originally Posted by unclebilly

Looking for a 944 hood.

[frosty2]

Looking for a set of front seat belts for a 73T, my interior is black.

Thanks
Mike

[unclebilly]

Originally Posted by tholyoak

I have one, going to depend on where you are though.

-Todd

Calgary area

[Jim2]

Originally Posted by unclebilly

Calgary area

Hood (no affiliation)


https://www.kijiji.ca/v-auto-body-parts/calgary/porsche-944-924-hood-for-sale/1575713163

[Sway Bar]

WTB- 2.7 Mahle Nikasil Cylinder set.

Someone must have on the shelf some Nikasil cylinders of same height group. Need a good set of (6) to finish rebuild.

Thanks,

Marlon

[Tomvwman]

Catalytic Converter Needed

1987 Porsche 930

93011323501 or 93011325300

Many Thanks
Tom

[TargaT]

complete 944 front wiper assembly. Not sure if year matters but its an 86 Turbo.

[Funcity]

Hello all

I’m looking for a 2 in muffler. I upgraded to SSI and need something “in the mean time” while waiting for a new M&K.
Doesn’t have to be anything fancy just something to keep me going!
Thanks!

[Jim2]

914-6 oil tank, anyone inside Canada have one for sale?

I know,.... better chance of finding a unicorn....

[Mark Henry]

Originally Posted by Jim2

914-6 oil tank, anyone inside Canada have one for sale?

I know,.... better chance of finding a unicorn....

I believe the best aftermarket option is one of Ben's tanks, he goes by the user name mb911 on 914world and likely he's on this site as well. He also has the console, neck and cap for the tank. He also has nice exhaust parts, GT oil cooler hard lines, etc.

Sorry no leads on a tank in Canada for a better deal than one of Ben's tanks.
Good luck

[Jim2]

I missed a factory tank which sold just three weeks ago. Dang.

Still have a couple other leads to chase down before going with Ben's.

[Mark Henry]

The thing about the factory tanks is they're steel with copper plating and they suffer from rust issues, only once have I seen a Canadian tank I'd put on my engine.

I have a DWD tank, Ben's and PMS tanks are based on that design, nice point is it adds about 1.5 quarts extra to the system. Ben's tanks come with stock cohline fittings, but you can special order -AN if you like.

[Jim2]

You make a point there Mark. I haven't held one in my hands so I'm overlooking the corrosion issue.

[coughpls]

Ideally in Canada .. if not will grab one in US ..

[rmrsfly4]

Looking for a CIS plastic air filter box cover. The piece with the snorkel
For my 2.4L
If you have one kicking around, let me know.
Thanks

[AlKidd]

Did you check with Randy at Whaletail?

Originally Posted by Jim2

914-6 oil tank, anyone inside Canada have one for sale?

I know,.... better chance of finding a unicorn....

[Jezebel]

Originally Posted by rmrsfly4

Looking for a CIS plastic air filter box cover. The piece with the snorkel
For my 2.4L
If you have one kicking around, let me know.
Thanks

Have this …

[Jp-oh]

Hi, I'm looking for the floorboard hardware that is used to adjust the clutch pedal throw. Can't seem to find it sold independent of the floor board.

Thanks

[Kerschbaumer]

Looking for a pair of 7x16 Fuchs - flat black with patina/mild fading - preferably on the west coast for my '82sc

Took my stock 6"/7" fuchs off - they have glossy black finish. I put on 8" fronts off a 951 and 9" rear from turbo - both with matte black finish that show some fading/age.

The 8's rub in the wheel well and actually bit into fender lip on a big hit - so I want to replace them with 7". I would use my 7's but the finish is different. I could get all 4 refinished to look the same but I actually like the patina - I like that my car shows some age and not interested to replace everything with new. If someone happens to have a pair of 7x16' with similar finish I may buy them and sell/trade my glossy 6/7's.

[upwardr]

I am looking for the connectors to install the CR-2001. The connectors look like a special style.