Parts Needed \ WTB

[Jim2]

Thanks Keith! I'll follow up with him.

Jim

[Mark Henry]

WTB 996 oil pump housing, it's 2003 3.6, but I believe they are all the same. Don't care about cosmetic, but pump gears, surfaces, etc, must be confirmed good no FOD condition.

[pors1968]

Originally Posted by Uwon

PM sent

0280140218
0280140201
0280140204
0280140206
have to check might some more any cis might works volk mercedes audi ect.

[jamesjedi]

WTB header adapters for a pair of Euro style headers.

[Hawkeye's-911T]

No.s 24 & 25 for 1970 T - I assume they only come in black.

I posted this in the classifieds in late Nov. - went overseas for a holiday & inadvertently deleted the two responses from our US friends.
I thought I'd retry here before re-posting again.

Cheers
JB

[Mark Henry]

Originally Posted by Hawkeye's-911T

No.s 24 & 25 for 1970 T - I assume they only come in black.

I posted this in the classifieds in late Nov. - went overseas for a holiday & inadvertently deleted the two responses from our US friends.
I thought I'd retry here before re-posting again.

Cheers
JB

If it's the same part number as on the 914/6, 914rubber.com has good reproductions.

[tholyoak]

I have this one. Send me an email if it will work and I can forward some more pictures.

Todd

Originally Posted by Mark Henry

WTB 996 oil pump housing, it's 2003 3.6, but I believe they are all the same. Don't care about cosmetic, but pump gears, surfaces, etc, must be confirmed good no FOD condition.

[Mark Henry]

Originally Posted by tholyoak

I have this one. Send me an email if it will work and I can forward some more pictures.

Todd

email sent

[911 Rod]

Originally Posted by 911 Rod

Looking for the male plug that is part of the AFM.
Anyone?

Still looking

[jamesjedi]

I will be doing my connecting rods for my 3.0 engine. I have ARP connecting rod bolts. Does someone have a the ARP stretch gauge to loan or buy.

[oilman]

Looking for an oil thermostat ( right rear wheel well) for an SC.

I believe it is PN 930.107.017.00

Thanks,

[pors1968]

Originally Posted by oilman

Looking for an oil thermostat ( right rear wheel well) for an SC.

I believe it is PN 930.107.017.00

Thanks,

I have one with good thread. 250.00 shipped

[Mr Beau]

Looking for an engine stand yoke for rebuilding an aircooled engine... Located in Edmonton.

[pors1968]

Originally Posted by Mr Beau

Looking for an engine stand yoke for rebuilding an aircooled engine... Located in Edmonton.

Check with bender706

[elt0m]

Anyone have a strutbar like this one?

[bdonally]

Before I order one, thought I'd check to see if anyone in eastern Ontario might have a P260 I could rent or borrow for a week or so in late April.
Thanks
Bob

[Mark Henry]

Originally Posted by bdonally

Before I order one, thought I'd check to see if anyone in eastern Ontario might have a P260 I could rent or borrow for a week or so in late April.
Thanks
Bob

Is this the 901 trans stack alignment tool?
I have a homemade ghetto trans tool cut out of an old tranny.
Central ontario, I will lend it but I would want it back in short order.

[bdonally]

Originally Posted by Mark Henry

Is this the 901 trans stack alignment tool?
I have a homemade ghetto trans tool cut out of an old tranny.
Central ontario, I will lend it but I would want it back in short order.

This is the gadget:




If you are wiling , I'd make sure all is ready to go before I got the tool.
Shouldn't take long but there is always the possibility of it not going smoothly..........nah , never happens
I'd actually prefer one made from a case rather than trust one of the plastic ones.
PM sent

[Mark Henry]

Sorry I thought you had a 901.

I'm looking for a scrap 915 stack housing to make this tool, free or cheap.
If I get one I'll mod and lend it to you.

[Jim2]

Mark, this housing?