PARTING Complete 1978 3.0 engine

[cudabnu]

was rebuilt back in 11/03, I have a copy of the shops receipt. Long story short, I purchased the car from back east and could not get it registered because it had a re-titled vin number, and no other supporting vin number, so the car was parted out. I was going to use it in a 1980 that I am building, but decided to go with a 3.6 conversion. Has a cat bypass, and Dansk stainless steel 1 in 2 out muffler that is almost new. The cat was plugged so it discolored the one side, then the cat was removed and a bypass put in, the 2 tips still need to be installed, but are included. Has new intake and injector seals, pop off valve, carrera chain tensioner upgrade. Dist. had been removed, so it needs to be put in and indexed correctly, New braided Beru plug wires, New Bosch coil. It only has about 2-300 miles on it since it was rebuilt, but looks like 1 of the throu bolts was leaking and they tried to put JB weld over it to stop the drip. Comes with clutch adn PP that look new (no ring gear), and fuel accumulator.
The fan does have 2 chips inthe back, and the fan housing does have a few cracks, one accross the mounting bolt for the coil that was helicoiled, but it still functions fine


NOW PARTING

78/79 Engine shroud $75
78/79 Fan housing (not perfect, but works) SOLD
78/79 Fan (1 chip in back, a little worn on hub corners ) $125
Alternator air deflector $50
Valero Alternator, int. reg. works good $SOLD
Complete CIS intake 78/79 large port $700 obo(includes 2 new straps, K&N filter, Carbon Fiber cover(pictured), and stock cover)
engine wiring harness, working, but some wire sheathings are cracked $120
Upper Valve covers $75 pair
Lower turbo valve covers $SOLD
Cam Towers $100 pr (1972 3 bearing towers)
3 bearing Cams $BO
Rockers $120 set
Cam hardware $40 pair (have 2 pairs)
Chain Cases $80 pair (have 2 pairs)
Carrera Tensioner kit, complete SOLD
Oil Pump $240
78/79 Distrubutor w/ new green signal wire $SOLD
NEW spare Distributor Signal Wire $50
almost new Beru braided plug wires (0 miles on them) SOLD
almost new Bosch coil and bracket $70, put on with wires, but never run
Thru Bolts/nuts/washers $50 set (I have 2 sets)
Rods $200 set
perfect Crank w/ nose bearing $900
Intermediate shaft $75 (also have another one from a 80 motor)
78 Case $800 (also have a 80 case in another ad that needs a stud removed and had part of the alt cradle welded for $450)
78/79 rebuilt heads, w/air injection block offs. $750
Nikasil Piston and Cylinders $500
24 Head Barrel nuts and washers, used, but look new $50
Dansk polished stainless sport muffler 1 in 2 out, SOLD
Catalytic converter bypass pipe $SOLD
Cylinder head air defector tins $50 set (have 2 sets)
Flywheel $75
Pressure Plate and Clutch $?
Engine support bar and cradle $125
Fuel accumulator and "S" line $75
Engine mounted oil cooler $150 ea(have 2)

Paypal payments are fine.
Shipping not included
I ONLY ship FEDEX, your package can be tracked at any time, and IF a claim needs to be made, It is way easier than dealing with a government agency!

[cudabnu]

[cudabnu]

[bmsr]

Hi cudabnu, I would like the cam towers, and also need the following - please let me know if you can help and prices:
-the large metal oil line from bottom of case
-starter
-headers
-the engine sheet metal piece across back of motor

[cudabnu]

I should have the tin piece and metal oil line on the bottom of the case, send me you email address and I'll get you some pics and prices. I only havew the stock heat exchangers with a CAT bypass, so I can't help you with headers.

dave (at) karmannghia (dot) com

[edgarcia737]

Would you sell the air filter cover? Both the stock and carbon fiber one. If so, how much with shipping to 85250.

Thx

[TibetanT]

PM and PayPal sent!

Thank you.

[cudabnu]

Ed, your pm box is full, email me with the little nuts and bolts you need and I'll toss them in when I ship on Monday

[TibetanT]

Yeah, I just noticed that a minute ago. Sorry about that.
I will Email you with the information probably tomorrow.

Have a good Turkey day off, and thanks again for your help with all my engine building needs!

[cudabnu]

Will trade any of my parts towards an ipad wifi 3G 32 or 64GB

[cudabnu]

bump, orig post updated.

[moparrob]

Dave, PM sent...

Rob

[TibetanT]

I got my parts!!

We had a snow storm come through which delayed the estimated delivery date.

Good pricing, fast shipping, awesome packaging, and parts were exactly as described in the Ad and pictures.

BUMP for a good seller.

[TibetanT]

Hello again:

I am interested in the following item if still available:

Cam Towers $120 pr


Thank you.


PM on the way.

[Daviboy]

PM sent

[LakeCleElum]

Cat bypass gone? If not, interested.

[jhelgesen]

PM sent

[cudabnu]

Cat bypass is sold, I've updated the orig. post.

[Vin-barrett]

I'll take
78/79 Distrubutor w/ new green signal wire $275

pm sent.. thanks

[Barskov]

Hi Dave

If you ship to EU ? , I would like a pair of chain cases .

its for a 2.7 mag case but I assume they will do in ALU ?

Kind regards
Uffe , Denmark