FS: 3.2 motronic engine

[Marv's3.2six]

sold sold sold sold sold



Revised listing

1988 3.2 Motronic engine
Strong running 3.2 freshened up 5k miles ago, top end rebuild & rod bearings. Complete with ECU & harness, light flywheel, 914 sheet metal, estimated @ 240-250hp, I am upgrading to 3.6
Leak down: 1-2%, 2-6%, 3-8%, 4-8%, 5-8%, 6-6% compression 165lb, all cyl ok.

$6500 obo, email for phone #,

1 5/8" 914 headers available (no heat)

[Markeydoo]

Will it fit in my car Marv
Mark

[Marv's3.2six]

Yes Mark it will fit any 914. Get yourself a copy of the current Excellence, April 2005. There is an 8 page article on 914 4 to 6 swaps.
The article says plan to spend $8-20k for the engine swap. Besides the cost of my engine its my guess that you'd spend approx $1k for the rest of the hard parts: forward engine mount, EFI fuel pump, 911 starter, muffler & bracket, throttle cable kit, etc....you'd have to eBay most stuff to get the good guy prices.

Its my guesstimate that you'll be at the very low end of the cost mentioned in the article. Have you priced just the 914-6 oil tank its $888.60 from Pelican. So do the math read the article, and then consider my 3.2 engine is ready to bolt in and run.

[Jim Dorociak]

would be interested in following your progress. What tranny, what year 3.6 all the particulars. thanks! Jim

I have a 1995 993 engine to be installed in my six. have not started, but started saving money and collecting parts.

jdorociak@adelphia.net

[Marv's3.2six]

Pics and additional information at the 914club classifieds
Link: http://www.914club.com/bbs2/index.php?act=ST&f=18&t=25330&

[Porsche Doc]

Originally posted by Marv's3.2six
Yes Mark it will fit any 914. Get yourself a copy of the current Excellence, April 2005. There is an 8 page article on 914 4 to 6 swaps.
The article says plan to spend $8-20k for the engine swap. Besides the cost of my engine its my guess that you'd spend approx $1k for the rest of the hard parts: forward engine mount, EFI fuel pump, 911 starter, muffler & bracket, throttle cable kit, etc....you'd have to eBay most stuff to get the good guy prices.

Its my guesstimate that you'll be at the very low end of the cost mentioned in the article. Have you priced just the 914-6 oil tank its $888.60 from Pelican. So do the math read the article, and then consider my 3.2 engine is ready to bolt in and run.

We did the install that was in the Excellence article.
It was a 3.0 CIS engine.
We do these conversions all the time. A 3.2 engine will fit in fit with a little work. The biggest thing you have to do is turn the intake manifold around 180 degres. Figure at least $5000 above the cost of the engine as a ball park. At least if you do it right!
The next thing thing we are doing to that 914 is 911 Carrera susp. conversion. Jim Pasha lives here in Knoxville TN. and we have help him with a bunch of his tech articles.
It will be in Excellance too.

[Marv's3.2six]

Bump- doesn't anybody want to make their 914 crazy fast?

[greglepore]

Marv-sent you an email earlier and a pm a couple days back about this with no reply. Could be tempted. Obviously some of the parts have been sold etc? What remains for 6500? Just the engine and stock intake, or are there other conversion parts still included? Can you estimate cost to palletize and ship to east coast?

[BURN-BROS]

Marv gave me a ride a while back and I can tell you it was a strong engine and his price looks good.

[greglepore]

Marv-sent you an offer via pm

[joe pitta]

Hi Marv .
if the 3.2 is still for sale let me know i will take it
but i think im to late Joe.

[D1A3]

I've been all over town and the April 2005 Excellence is either sold out or already replaced with the May issue. Does anybody know of this article being online or available elsewhere? I'm interested in the Excellence article specifically.

Thanks!