|
|
|
|
| Author |
|
|
Registered
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,366
|
Replacment pins for Cam Holding Tool?
Anyone know where to get replacement pins?
|
||
11-11-2024, 01:42 AM
|
|
|
It's a 914 ...
Join Date: Jan 2008
Location: Ossining, NY
Posts: 4,685
|
Not sure if they are a stand size i.e. available from Porsche parts suppliers, but McMaster is a good place for generic hardware items like pins
|
||
|
11-11-2024, 04:08 AM
|
|
|
Registered
Join Date: Dec 2014
Posts: 13,814
|
You’ll have to make your own pin.
__________________
House producers wanted to end the show after season 8 to keep the enigmatic appeal of the central character and maintain the show's mystique. Ahhh The Mystique!!! |
||
|
11-11-2024, 04:11 AM
|
|
|
Registered
Join Date: Jan 2022
Posts: 159
|
Hi
You may be able to use the rollers from a roller bearing. These come in various diameters and lengths. You can buy them individually, (or in small quantities) from your local bearing supplier. Cheers |
||
|
11-11-2024, 03:18 PM
|
|
|
Registered
Join Date: Oct 2008
Location: Nash County, NC.
Posts: 8,467
|
I believe they’re flat spotted on the inside of the pin.
Regardless, I’m sure it’s all metric. Bruce |
||
|
11-11-2024, 05:33 PM
|
|
|
Registered
Join Date: Dec 2014
Posts: 13,814
|
Get a micrometer measure pin, buy a steel rod off McMaster, grind a flat spot, pound in, done.
__________________
House producers wanted to end the show after season 8 to keep the enigmatic appeal of the central character and maintain the show's mystique. Ahhh The Mystique!!! |
||
|
11-12-2024, 04:27 AM
|
|
|
|
Registered
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,366
|
Thanks Guys... I removed a pin again and noticed the "flat" goes quite far down on the pin. Actually enough that you can cut-off the part that "sticks out" and have enough flat to reinstall.
In any case, measured and they're 6.00mm X 40mm. So have a few 6mm gauge pins coming. |
||
|
11-13-2024, 11:55 AM
|
|
|
Registered
Join Date: Dec 2014
Posts: 13,814
|
Make sure tool is flush with sprocket and pins are all the way in before torquing on it.
__________________
House producers wanted to end the show after season 8 to keep the enigmatic appeal of the central character and maintain the show's mystique. Ahhh The Mystique!!! |
||
|
11-22-2024, 07:33 AM
|
|
|
Registered
|
When I am looking for bits like that I find drill shanks useful. Come in a range of sizes - metric and imperial. :-)
Alan
__________________
83 SC, 82 930 (track) - Stock except for RarlyL8 race headers, RarlyL8 Zork, K27-7006, 22/28 T bars, 007 Fuel head, short 3&4 gears, NGK AFR, Greddy EBC (on the slippery slope), Wevo engine mounts, ERP rear camber adjust and mono balls, Tarret front monoball camber adjust, Elgin cams, 38mm ported heads, 964 IC. 380rwhp @ 0.8bar Apart from above, bone stock:-) |
||
|
11-29-2024, 03:23 PM
|
|
|
Registered
Join Date: Dec 2007
Location: Just a little north of 13669/Nation's capital
Posts: 1,279
|
Good tip Alan L !
__________________
1986 Targa Guards Red 2021 MT09 SP |
||
|
12-01-2024, 06:07 AM
|
|
|
Banned
Join Date: Dec 2024
Posts: 5
|
You might have to make your own opinion
|
||
|
12-01-2024, 03:15 PM
|
|
|
Registered
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,366
|
Just tried my mine again after I pulled out a pin and chopped it off. Works great again.
|
||
|
12-02-2024, 02:01 PM
|
|
|
|
Registered
Join Date: Oct 2003
Location: Central Fla
Posts: 1,864
|
McMaster-Carr
__________________
The two most useless things to a driver are the braking distance behind you and nine-tenths of a second ago. |
||
|
12-03-2024, 01:57 AM
|
|
 |
| Thread Tools | |
| Rate This Thread | |
|
|
