Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > 911 Engine Rebuilding Forum


Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered
 
JoeMag's Avatar
 
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,367
How can you clean fuel rails?

Have some fuel rails I'm going to be using and I notice rust forming in them. Can these be cleaned up? If so, where?

Old 07-29-2008, 08:49 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #1 (permalink)
Registered
 
3.2 CAB's Avatar
 
Join Date: Dec 2003
Location: MS.
Posts: 2,322
Are they the ones used on a 3.2? If so, you can clean them at home just fine. Make sure to plug all of the holes, so you don't get any crap or anything else, inside the fuel rails. I have used a soft, wire wheel, brush either on my bench grinder or on one of my angle or side-grinders. Clean the rusted spots down to clean metal and give the rest a good general cleaning. If you want a "factory new"type of look, there are paint kits that will closely resemble the original yellowish colored, cadmium plating. If not that, you could prime and then use almost any color of paint for engines or transmissions, due to the heat that the fuel rails will be subjected to. It should come out really nice. Good luck!! Tony.
__________________
84' Steelslantnose Cab.
1953 Dodge B-4-B-108" 90,127 miles
1953 Dodge B-4-C-116" 58,146 miles
1954 Dodge C-1-B8-108" 241V8 POLY
1973 Roadrunner 440-SIX-PACK*
1986 F-250 Super Cab-460 V8 tow
Newest additions-
Matching numbers 1973 340 Road Runner!!
1948 Dodge B-1-F-152" 1-1/2 ton Dump body, 39,690 miles
others...
Old 07-29-2008, 09:17 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #2 (permalink)
Registered
 
JoeMag's Avatar
 
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,367
...to clarify. The INSIDE of fuel rail has some rust forming.
Old 07-29-2008, 10:00 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #3 (permalink)
Registered
 
3.2 CAB's Avatar
 
Join Date: Dec 2003
Location: MS.
Posts: 2,322
Ohhh,... OK. That is a totally different matter. I don't have an answer for you on that.
__________________
84' Steelslantnose Cab.
1953 Dodge B-4-B-108" 90,127 miles
1953 Dodge B-4-C-116" 58,146 miles
1954 Dodge C-1-B8-108" 241V8 POLY
1973 Roadrunner 440-SIX-PACK*
1986 F-250 Super Cab-460 V8 tow
Newest additions-
Matching numbers 1973 340 Road Runner!!
1948 Dodge B-1-F-152" 1-1/2 ton Dump body, 39,690 miles
others...
Old 07-29-2008, 04:46 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #4 (permalink)
abit off center
 
cgarr's Avatar
 
Join Date: Feb 2002
Location: At the Airport Kentwood, MI
Posts: 7,311
Garage
Send a message via Yahoo to cgarr
You been running a lot of fuel with alcohol in it? May have since thats about all you can get now. Most likely your tank and lines are a but rusty too. You could shake some lead or steel shot in it to clean it up but its going to come right back I would guess. I always run a shot of MM oil with the fuel.
__________________
______________________
Craig
G2Performance
Twinplug, head work, case savers, rockers arms, etc.
Old 07-29-2008, 05:23 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #5 (permalink)
Registered
 
JoeMag's Avatar
 
Join Date: Jul 2005
Location: Cleveland, OH
Posts: 1,367
Craig -- intestesting thought. ...i have no idea what was run in these. they've been off what ever car they came from for a while. what is MM oil?
Old 07-30-2008, 07:32 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #6 (permalink)
 
abit off center
 
cgarr's Avatar
 
Join Date: Feb 2002
Location: At the Airport Kentwood, MI
Posts: 7,311
Garage
Send a message via Yahoo to cgarr
MM=Marvel Mystery Oil

__________________
______________________
Craig
G2Performance
Twinplug, head work, case savers, rockers arms, etc.
Old 07-30-2008, 07:41 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #7 (permalink)
Reply


 


All times are GMT -8. The time now is 05:25 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.