|
|
|
|
| Author |
|
|
Brando
|
piston pin circlip replacement
So I'm short on circlips, Didn't get any from our host for whatever reason...
And I want to procede. I just bought some 7/8 piston retainers from pepboys that look to be the right size to fit in there. Theyre flat, not round, and have little circle/holes on the end of each side(youve seen them) for installing/removing with a tool. Can anyone tell me not to instal these for a good reason? I really want to move forward without waiting another 4 days. Total cost for a crapload $7.50 and I have a reciept so I'll take them back. Thanks, BA |
||
02-26-2011, 08:56 AM
|
|
|
Registered
|
how much is your rebuild? Mine was 12k. based on this huge investment, I would not use circlips that do not fit as intended to save 4 days. its a corner cut that just isnt worth it.
__________________
83 SC Targa -- 3.2SS, GT2-108 Dougherty Cams, 9.5:1 JE Pistons, Supertec Studs, PMO ITB's, MS2 EFI, SSI's, Recurved Dizzy, MSD, Backdated Dansk Sport Stainless 2 in 1 out, Elephant Polybronze, Turbo Tie Rods, Bilstein HD's, Hollow 21-27 TBs, Optima Redtop 34R, Griffiths-ZIMS AC, Seine Shifter, Elephant Racing Oil Cooling. |
||
|
02-26-2011, 05:57 PM
|
|
|
Brando
|
Hahahahahaha!
That's a pretty good point. |
||
|
02-26-2011, 06:10 PM
|
|
|
Registered
Join Date: Dec 2002
Location: SE Wisconsin USA
Posts: 34
|
Square snap ring in a round ring groove ... not a good idea.
__________________
Thanks, Jim 64 356 - SC Street Concours 92 964 - C2 Track 97 993 - C4S Street (gone) 12 997.2 TTS Street |
||
|
02-28-2011, 02:46 PM
|
|
|
Registered
Join Date: Jul 2003
Location: Valencia Pa.
Posts: 8,859
|
It pays to be patient. How dumb would you feel while your are taking it all back apart to fix it again if they did not stay in there?
If there is one lesson I have learned in all my years of wrenching,... it is always easier and faster to do it right the first time.
__________________
No left turn un stoned |
||
|
02-28-2011, 02:52 PM
|
|
|
abit off center
|
So whats with many now using the spiral circle clips (spirolox) now a days. We have used these at work on clutches for years but now see them working there way in as pistons clips. They are an amazing clip and very easy to install and remove.
__________________
______________________ Craig G2Performance Twinplug, head work, case savers, rockers arms, etc. Last edited by cgarr; 02-28-2011 at 03:30 PM.. |
||
|
02-28-2011, 03:25 PM
|
|
|
|
Chain fence eating turbo
Join Date: Dec 2008
Location: Austin, TX
Posts: 9,131
|
Quote:
__________________
Cory - turbo'd '87 C3.2 Guards/Blk, 3.4, 7.5:1 CR, 993SS cams, Borg-Warner S366 turbo @ 1.2-1.5 bar, Treadstone full bay IC, 70mm TB, TiAL F46 WG, HKS 1 1/2" BOV, twin 044 pumps, MicroSquirt AMP'd w/GM smart coilpack, Bilstein coilovers, Tramont replica Speedlines (285's rr, 225's frt), Big Reds frt, 993 rr., tower brace, MOMO wheel |
||
|
03-01-2011, 03:32 AM
|
|
|
Registered
Join Date: Jun 2003
Location: Granada Hills
Posts: 381
|
Call Don at EBS for the clips. Get the install tool from Stomski Racing.
|
||
|
03-01-2011, 08:50 AM
|
|
|
Registered
Join Date: Jan 2004
Location: CT
Posts: 11,552
|
Let me know how many you need and send me your mailing address...I'll send some out no charge
__________________
Tom Butler 1973 RSR Clone 1970 911E 914-6 GT Recreation in Process |
||
|
03-01-2011, 08:57 AM
|
|
|
Brando
|
I don't need free, Give me a # and I'll paypal you for them and shipping.
__________________
Turbo powa! 1977 911s. it's cool |
||
|
03-03-2011, 09:10 AM
|
|
hoonkraft
1969 and 1986 Porsche Targa and Coupe 1720cc and 3
