|
|
|
|
| Author |
|
|
Registered User
Join Date: Jan 2011
Posts: 17
|
88 3.2 Cylinder Head Gasket
I don't remember while disassembling the engine it has a cylinder head gasket. Even the Rebuilding gasket kit doesn't have the cylinder head gasket.
|
||
03-11-2017, 12:25 PM
|
|
|
Chain fence eating turbo
Join Date: Dec 2008
Location: Austin, TX
Posts: 9,115
|
No cylinder gaskets in a 3.2
|
||
|
03-11-2017, 01:05 PM
|
|
|
Registered User
Join Date: Jan 2011
Posts: 17
|
Thanks!
|
||
|
03-11-2017, 01:44 PM
|
|
|
Chain fence eating turbo
Join Date: Dec 2008
Location: Austin, TX
Posts: 9,115
|
No prob.
|
||
|
03-11-2017, 02:36 PM
|
|
|
Registered
Join Date: Sep 2015
Location: Costa Rica and Pennsylvania U.S.
Posts: 3,301
|
head gasket 3.2
There is a repair headgasket for the 3.2.Part # 930-104-381-01.It is 0.50 mm thick with a silicone type coating for better seal.If you have to resurface the head & the top of the cylinder this gasket will keep the height correct.Work great on Turbo motors.Fred
|
||
|
03-11-2017, 06:07 PM
|
|
|
abit off center
|
That number comes up for a 964, will that work with the 3.2?
__________________
______________________ Craig G2Performance Twinplug, head work, case savers, rockers arms, etc. |
||
|
03-12-2017, 12:30 PM
|
|
|
|
Registered
Join Date: Sep 2015
Location: Costa Rica and Pennsylvania U.S.
Posts: 3,301
|
head gasket
Hi Craig,I am going off memory on the part #.Originally used these on 3.2.Opened them up to 97.98 & 100 mm to use as head gasket on all kinds of applications.Maybe I am off by a digit on the number.I am in C.R. for a few more weeks.I have them on the shelf so I will get the number then.Great gasket with no leaks or sweat.I have used at least 100 sets with perfect results.Only buy Porsche O.E.M as the aftermarket ones do not have the coating.I believe the originals are made of Incanel.Fred
|
||
|
03-12-2017, 03:19 PM
|
|
|
abit off center
|
I would like the head gasket as on option for a customer. I have a set of heads in that had the sealing surfaces so poorly cut they will be at -.50mm when done. It's either thicker base gaskets or some type of head gasket?
Sent from my iPhone using Tapatalk
__________________
______________________ Craig G2Performance Twinplug, head work, case savers, rockers arms, etc. |
||
|
03-12-2017, 03:27 PM
|
|
|
Schleprock
Join Date: Sep 2000
Location: Frankfort IL USA
Posts: 16,639
|
Fred is correct that part number is a head gasket for the 964 Turbo. It's number 8 in the diagram for the M30.69 turbo engine
 
__________________
Kevin L '86 Carrera "Larry" |
||
|
03-13-2017, 07:38 AM
|
|
|
Member 911 Anonymous
|
Masters CGarr & KTL,
Won't the gasket require a slot in the head to accommodate the gasket ( aka heat ring ), like the 964 head?
__________________
'85 Carrera Targa Factory Marble Grey/Black * Turbo Tail * 930 Steering Wheel* Sport Seats * 17" Fuchs (r) * 3.4 * 964 Cams * 915 * LSD * Factory SS * Turbo Tie Rods * Bilsteins * Euro Pre-Muff * SW Chip on 4K DME * NGK * Sienes GSK * Targa Body Brace PCA/POC |
||
|
03-13-2017, 07:53 AM
|
|
|
Forced Induction Junkie
|
I don't think the head gasket in question (M30-69 engine) will work on a 3.2. Gasket is designed for 97mm bores.
I measured the ID of head gasket... approx. 97.135mm
__________________
Dave '85 930 Factory Special Wishes Flachbau Werk I Zuffenhausen 3.3l/330BHP Engine with Sonderwunsch Cams, FabSpeed Headers, Kokeln IC, Twin Plugged Electromotive Crankfire, Tial Wastegate(0.8 Bar), K27 Hybrid Turbo, Ruf Twin-tip Muffler, Fikse FM-5's 8&10x17, 8:41 R&P Last edited by WERK I; 03-13-2017 at 08:58 AM.. |
||
|
03-13-2017, 08:31 AM
|
|
1969 and 1986 Porsche Targa and Coupe 1720cc and 3
Marble Grey
1985 Porsche 930 Fac. Slantnose 3.3l
