Parts Needed \ WTB

[rywats]

Pm’d

[mnez]

Pm'd

[Jim2]

Looking for euro H4 chrome trim rings, inside Canada.

Thx.

[TargaT]

Hi, looking for any suspension upgrade parts, torsion bars, monoballs, Bilstein HD shocks etc. Let me know what you have. I will be ordering new parts in the next few days.
76 911

Thanks, Joe, jd@dren.ca

[911 Rod]

Originally Posted by TargaT

Hi, looking for any suspension upgrade parts, torsion bars, monoballs, Bilstein HD shocks etc. Let me know what you have. I will be ordering new parts in the next few days.
76 911

Thanks, Joe, jd@dren.ca

I have the stock t bars for my 86 if you are interested.

[gtihop]

I have stock green rear bilsteins from an 83. And also front bilstein inserts for Bilstein housings

[rywats]

Originally Posted by TargaT

Hi, looking for any suspension upgrade parts, torsion bars, monoballs, Bilstein HD shocks etc. Let me know what you have. I will be ordering new parts in the next few days.
76 911

Thanks, Joe, jd@dren.ca

There is an add on kijiji - brand new Bilstien b6 inserts

[TargaT]

Thanks guys, I bought the inserts from the ad already. Shocks I'd be looking for new or close HDs.
T bars could be used but thicker than stock.

[Cook&Dunning]

Give Randy at Whaletail a call - he probably has them (If you haven't already)

[mnez]

I have the 22mm Tarett Engineering adj rear sway bar from my 86 911, but Tarett shows a different one for 65-77 vs 78-89.
PM me if interested anyway.
Mike

Originally Posted by TargaT

Hi, looking for any suspension upgrade parts, torsion bars, monoballs, Bilstein HD shocks etc. Let me know what you have. I will be ordering new parts in the next few days.
76 911

Thanks, Joe, jd@dren.ca

[haycait911]

need a hook style targa top.

[panzerfaust]

a buddy gave me some custom SR dampers to try out since he has revamped his suspension to all elephant vons. too many pot holes in MI for me and want to run softer dampers.

i may have some upgraded, bilstein sport dampers inserts i will be pulling out once it gets warm enough. i think they are tuned for 22mm 29mm TBs.

[Mark Henry]

Looking for a 2003 3.6 996 IMS shaft. 2000-2005 internal tooth intermediate shaft from 996 or boxster, will work.
99610501564

[Hawkeye's-911T]

I am in need of a parcel shelf in decent condition for a rust rehab project on a 1970. Thanks

Cheers
JB

[Hawkeye's-911T]

Hi panzefaust
I received a notification in my e-mail inbox - I don't see your post. Should I try and PM you? In case I was unclear - I require the steel panel portion.
Cheers
JB

[panzerfaust]

my mistake... i deleted it because i reread your post and its a 70. my parcel shelf is a mid style like 75 to late sc i think

sorry about that

[Hawkeye's-911T]

Hey - no worries - it was worth a shot. Still holding out hope for a response - though it's starting to look like I'll have to go the 'repro' route. More $$$$ down the 'resto-rabbit-hole'.

Cheers
JB

[pors1968]

Originally Posted by Hawkeye's-911T

Hey - no worries - it was worth a shot. Still holding out hope for a response - though it's starting to look like I'll have to go the 'repro' route. More $$$$ down the 'resto-rabbit-hole'.

Cheers
JB

Do you need complete or the upper part.PM you e-mail .i have 70 and couple that would fit if you not resto concours Richard

[Hawkeye's-911T]

Hi Richard

Thanks for your reply. Although I haven't decided at this point, I am seriously considering going with one of Restoration Design's repros - a little more pricey than I'd hoped but all should be 'correct' as far as the resto job in the parcel shelf area goes.

Cheers
JB

[pors1968]

Originally Posted by Hawkeye's-911T

Hi Richard

Thanks for your reply. Although I haven't decided at this point, I am seriously considering going with one of Restoration Design's repros - a little more pricey than I'd hoped but all should be 'correct' as far as the resto job in the parcel shelf area goes.

Cheers
JB

No problem Doing same job on my 70 changing parcel shelf and seat area .