Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > Porsche 911 Technical Forum


Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered
 
Join Date: Feb 2001
Location: South of the Mason-Dixon Line
Posts: 3,722
Why A Rough Idle After Tune-Up?

I changed out my spark plugs, replaced my fuel filter and changed the oil and oil filter and after start up, it idles a bit rough. Its the 2.4, 1973.5T CIS engine. I went back to check my spark plug connectors, make sure I did not bump any vacuum, gas or electrical lines, and yet its till on the rough side. On the road it runs like a bat outta hell in all gears throughout the rpm ranges, but its very peculiar why this happened.

Can new spark plugs cause an issue? Richen up the mixture?

Any advice is always appreciated from you folks.

Thanks
Bob

73.5T - CIS

Old 05-12-2005, 11:12 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #1 (permalink)
Registered
 
copper's Avatar
 
Join Date: Sep 2004
Location: Ontario Canada
Posts: 1,031
Garage
Although you didn't mention it, I assume you gapped your plugs correctly...
__________________
Jim Dean LL.B. - London, Ont, Canada.
1969 911T "Blood Orange" Euro (Brought over from Germany in 86)
Engine and brake system rebuilds 2006 & 2007
"Oversteer scares passengers, understeer scares drivers."
Old 05-12-2005, 11:21 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #2 (permalink)
Registered
 
Join Date: Feb 2001
Location: South of the Mason-Dixon Line
Posts: 3,722
I used the right plugs and gapped correctly. The idle is a slight intermittent miss, that although is not very pronounced, was not present before. Its a mystery to me.


Bob
Old 05-12-2005, 12:49 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #3 (permalink)
Registered
 
Join Date: Dec 1999
Location: Novato, CA
Posts: 4,740
Assuming your ignition cables are old stock Beru, disturbing them with a tune up might be enough to cause them to fail.

Joe
Old 05-12-2005, 01:16 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #4 (permalink)
Designer King
 
Paulporsche's Avatar
 
Join Date: Mar 2004
Location: Toronto, ON Canada
Posts: 5,499
Assuming you used the same/ correct plugs.
Did you check your rotor, cap,timing, and dwell?
Maybe your dwell & timing are off but you didn't notice it before.
__________________
Paul
Yellow 77 Sunroof Coupe/cork interior; 3.2L SS '80 engine/10.3:1/No O2; Carrera Tensioners; 11 Blade Fan; Turbo tie rods; Bilstein B6; 28 tube Cooler; SSI, Dansk; MSD/Blaster; 16x7" Fuchs/205/50 Firestone Firehawk Indy 500s; PCA/UCR, MID9
Never leave well enough alone
Old 05-12-2005, 02:35 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #5 (permalink)
Registered
 
Join Date: Dec 1999
Location: Novato, CA
Posts: 4,740
If you have a pop off valve you might make sure it's seated.

Joe

Old 05-13-2005, 07:49 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #6 (permalink)
 
Reply


 


All times are GMT -8. The time now is 06:46 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.