Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > Porsche 911 Technical Forum


Reply
 
LinkBack Thread Tools Rating: Thread Rating: 1 votes, 1.00 average.
Author
Thread Post New Thread    Reply
Registered
 
arbita1's Avatar
 
Join Date: Aug 2004
Location: Mahopac, NY
Posts: 2,334
Garage
Ok. Let me take a step back here.

I'm using the same ring and pinion that came with the transmission. And I'm using all the same shim packs it came with. The P/S bearing was re-used as it was determined by the machine shop to still be in good condition. The only thing that was changed were the carrier bearing and races.

Based on the above my understanding is that I should not have changed any differential settings.

It turns out I do have a torque wrench that goes as low as 10 ft-lbs. So I torqued the nuts to 18 ft-lbs (which is the higher end of the spec and it was too tight for the ring gear to move).

Is it possible that the bearing races are not fully seated?

__________________
Matt.

83 911SC
85.5 944 NA - Sold
Old 04-22-2009, 03:39 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #41 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
"Is it possible that the bearing races are not fully seated?"

This is possible if you think about it logically but if you used a press they should be full home. Even if you didn't use a press you would be able to tell by looking at them. Are the races full seated in the case and side cover? Are the bearings tight against the spacers on the diff? I'm guessing yes to both of these questions.

Hopefully Peter Zimmerman will chime in shortly. (he almost always does on the gearbox posts)

I hope I haven't ruined your day but the reason I made that post is because of other threads I have read on the subject of pre load and backlash. I'm re assembling my troubled gearbox at the moment and here is a link to my thread...

915 Shift fork check with an unexpected outcome

I have created a word document with lots of detailed information about this stuff.

I'll send you a message with my Hotmail email address shortly so I can send you this document. It's about 22 pages long with lots of diagrams and pictures.
__________________
- Peter

Last edited by sc_rufctr; 04-22-2009 at 04:45 AM..
Old 04-22-2009, 03:56 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #42 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
This is a picture from the Porsche work shop manual. (stolen from another thread)

Please read the section under "Ring gear has to be adjusted, if"

__________________
- Peter
Old 04-22-2009, 04:09 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #43 (permalink)
Bird. It's the word...
 
Fishcop's Avatar
 
Join Date: Feb 2001
Location: Port Macquarie NSW Australia
Posts: 5,077
Garage
Peter, may I please get a copy of your work also?

Cheers
John
__________________
John Forcier
Current: 68L 2.0 Hotrod - build underway
Old 04-22-2009, 04:55 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #44 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
Just sent you a PM with my email address. I'm a bit reluctant to post it here.
__________________
- Peter
Old 04-22-2009, 05:04 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #45 (permalink)
Registered
 
Peter Zimmermann's Avatar
 
Join Date: May 2008
Posts: 2,948
Quote:
Originally Posted by arbita1 View Post

I'm using the same ring and pinion that came with the transmission. And I'm using all the same shim packs it came with. The P/S bearing was re-used as it was determined by the machine shop to still be in good condition. The only thing that was changed were the carrier bearing and races.

It turns out I do have a torque wrench that goes as low as 10 ft-lbs. So I torqued the nuts to 18 ft-lbs (which is the higher end of the spec and it was too tight for the ring gear to move).

Is it possible that the bearing races are not fully seated?
Whew, this isn't easy to do via "long distance." FYI: Side cover nut torque will not affect bearing pre-load after the nuts are tight. Using only four (for example) equally spaced nuts to make the measurement might not give you a perfect measurement. Here are my questions:

1. Are you sure that both carrier bearing races are fully seated (one in the housing & one in the side cover)? You can see if they are by simply looking at the back side of each race through the axle flange hole.

2. At this point forget all about pinion depth and backlash, it just confuses this issue.

3. When you removed your old carrier bearings I will assume that you did them one at a time, pulled off any shims under them, and cleaned the shims thoroughly, correct?

4. Did you damage a shim while having trouble removing the one bearing?

5. Did you notice that the shims (not the .25mm super-thin ones) have a square cut on one side, and a bevel on the other. Are you absolutely sure that the bevel is facing the diff on each of the thick shims?

Answer these items and then we'll move on to how you are trying to get the ring gear to turn with the side cover torqued.

In order to correctly measure pre-load you need the following, the washer is homemade and is a snug fit at the ID (35mm), and I had to bevel the outer edge to face the diff because it was a little too wide (7.4mm) and I didn't have access to a lathe (my washer is 2.6mm thick):






__________________
Keep the Shiny Side UP!
Pete Z.

Last edited by Peter Zimmermann; 04-22-2009 at 07:41 AM..
Old 04-22-2009, 07:18 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #46 (permalink)
 
Registered
 
arbita1's Avatar
 
Join Date: Aug 2004
Location: Mahopac, NY
Posts: 2,334
Garage
Quote:
Originally Posted by Peter Zimmermann View Post
Whew, this isn't easy to do via "long distance."
No kidding. Feel like taking a trip to NY and doing this for me???

Here are my questions:

1. Are you sure that both carrier bearing races are fully seated (one in the housing & one in the side cover)? You can see if they are by simply looking at the back side of each race through the axle flange hole.

No I am not. The machine shop put the new races in for me and I assume they know what they are doing. I'll take pictures tonight and post them so you can tell me what you think.

2. At this point forget all about pinion depth and backlash, it just confuses this issue.

OK.

3. When you removed your old carrier bearings I will assume that you did them one at a time, pulled off any shims under them, and cleaned the shims thoroughly, correct?

Yes...this is correct.

4. Did you damage a shim while having trouble removing the one bearing?

No, because I didn't pull from the bottom, I pulled from the top lip of the race after I removed the rollers.

5. Did you notice that the shims (not the .25mm super-thin ones) have a square cut on one side, and a bevel on the other. Are you absolutely sure that the bevel is facing the diff on each of the thick shims?

I remember seeing the square cut...but do not remember the bevel. I checked the factory manual to see if there was a certain position for the square cut, but didn't find anything, so I didn't think there was a special position for it.

Answer these items and then we'll move on to how you are trying to get the ring gear to turn with the side cover torqued.
Hopefully this will shed some light on things.
__________________
Matt.

83 911SC
85.5 944 NA - Sold
Old 04-22-2009, 08:20 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #47 (permalink)
Registered
 
Peter Zimmermann's Avatar
 
Join Date: May 2008
Posts: 2,948
Quote:
Originally Posted by arbita1 View Post
Hopefully this will shed some light on things.
The light is brighter!

Sorry, but you might have to pull those bearings back off. This will be very difficult, to not damage them, with the tools you have, so we'll try something else first.

Use a mag light, or similar, to light the area under each bearing. Look at the side/edge of the shims and check to see if they are standing proud from the carrier surface, or if they appear to be firmly seated against the carrier. I have an old diff in the garage (see next post) that I'll look at later to see if this approach will help us...
__________________
Keep the Shiny Side UP!
Pete Z.

Last edited by Peter Zimmermann; 04-22-2009 at 11:03 AM..
Old 04-22-2009, 08:45 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #48 (permalink)
Registered
 
Peter Zimmermann's Avatar
 
Join Date: May 2008
Posts: 2,948
Matt: Please don't miss post # 48!

Here are a couple of pics for you; I've never experimented with putting the shims on square side down, but I imagine that will only be a few thousandths difference. That said, in this biz even a spec of hard dirt makes a difference.

If you have one or both shims upside down hopefully you'll be able to detect a space using feeler gauges.

__________________
Keep the Shiny Side UP!
Pete Z.

Last edited by Peter Zimmermann; 04-22-2009 at 11:03 AM..
Old 04-22-2009, 11:00 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #49 (permalink)
Registered
 
arbita1's Avatar
 
Join Date: Aug 2004
Location: Mahopac, NY
Posts: 2,334
Garage
I'll take pictures when I get home.
__________________
Matt.

83 911SC
85.5 944 NA - Sold
Old 04-22-2009, 11:02 AM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #50 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
Peter Zimmerman

You post the best pictures... You should write a book about the 915 gearbox.
__________________
- Peter
Old 04-22-2009, 04:07 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #51 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
PM from Porsche Monkey replied to.
__________________
- Peter
Old 04-22-2009, 04:41 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #52 (permalink)
 
Registered
 
Peter Zimmermann's Avatar
 
Join Date: May 2008
Posts: 2,948
Quote:
Originally Posted by sc_rufctr View Post
Peter Zimmerman

You post the best pictures... You should write a book about the 915 gearbox.
Thank you, sir!
__________________
Keep the Shiny Side UP!
Pete Z.
Old 04-22-2009, 04:51 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #53 (permalink)
Slumlord
 
Porsche_monkey's Avatar
 
Join Date: May 2001
Location: Canada
Posts: 4,983
Quote:
Originally Posted by sc_rufctr View Post
Peter Zimmerman

You post the best pictures... You should write a book about the 915 gearbox.
Don't print more than 100 copies. We are the proud, the few, the 915 rebuilders.
__________________
84 Cab - sold!
89 Cab - not quite done
90C4 - winter beater
Old 04-22-2009, 05:10 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #54 (permalink)
Registered
 
arbita1's Avatar
 
Join Date: Aug 2004
Location: Mahopac, NY
Posts: 2,334
Garage
Ok. I pull the differential back out of the case and looked at the bearings. Here are some pictures...









But I don't think this is where my problem lies...see next post there will be more pictures.
__________________
Matt.

83 911SC
85.5 944 NA - Sold
Old 04-22-2009, 05:43 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #55 (permalink)
Registered
 
arbita1's Avatar
 
Join Date: Aug 2004
Location: Mahopac, NY
Posts: 2,334
Garage
I decided to put the differential back in the case and spin it without the side cover on.

It spun freely, but I would hear it get caught up on something at every cycle. It seemed like the speed sensor was rubbing against something...



What the hell is this?



And this?



And this.



Does that look right?

I'm slowly getting that sinking feeling.
__________________
Matt.

83 911SC
85.5 944 NA - Sold
Old 04-22-2009, 05:47 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #56 (permalink)
Bird. It's the word...
 
Fishcop's Avatar
 
Join Date: Feb 2001
Location: Port Macquarie NSW Australia
Posts: 5,077
Garage
Looks like someone has welded up the crack from the back (inside). It is a really thin bit of alloy casting between the diff magnets and the external sensor... But no reason it can't be cleaned up.
__________________
John Forcier
Current: 68L 2.0 Hotrod - build underway
Old 04-22-2009, 06:01 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #57 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
Quote:
Originally Posted by Fishcop View Post
Looks like someone has welded up the crack from the back (inside). It is a really thin bit of alloy casting between the diff magnets and the external sensor... But no reason it can't be cleaned up.
x2... The 915 castings are not perfect. Don't stress about it. If you can clean up that weld without compromising it then it should be fine.

The crack from the outside is a worry but the weld from the inside can be re done and ground flat. This won't cost mush to fix.

Think of it this way. It's so much better that you found this now rather than after it was back together and in the car. So in a way this is a good thing... Well done.

This reminds me of something a Doctor told me when I was in training to become a nurse...

More is missed from not looking that not knowing.
__________________
- Peter
Old 04-22-2009, 06:19 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #58 (permalink)
Almost Banned Once
 
sc_rufctr's Avatar
 
Join Date: Feb 2009
Location: Adelaide South Australia
Posts: 38,355
Send a message via MSN to sc_rufctr
Quote:
Originally Posted by arbita1 View Post
Ok. I pull the differential back out of the case and looked at the bearings. Here are some pictures...



But I don't think this is where my problem lies...see next post there will be more pictures.
Just a thought... This is an SKF bearing.

Was the old one you removed an SKF? or the original OEM one from the factory?
I just looked at mine and I can't see any marking on it like yours in the photo so I'm assuming it's OEM
and therefore not manufactured by SKF. (or it may be unbranded but made by SKF)

You would assume that the bearings would be the same size externally regardless of the manufacturer but we need to confirm this measurement.

Do you still have the old ones? Are you able to accurately measure their stacked height?

The Genuine Porsche ones are: OEM-999-059-027-00 - $80.25
SKF Part number from our host: 999-059-027-00-M92 - $25.00
(Both available through our host)

Again... Peter Zimmerman should be able to confirm this measurement as he probably has a box full of old OEM and SKF bearings.
__________________
- Peter
Old 04-22-2009, 07:54 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #59 (permalink)
SP2 SP2 is offline
Registered
 
SP2's Avatar
 
Join Date: Apr 2006
Location: Newcastle, WA
Posts: 966
What a great thread!

__________________
James

1969 911E Slate Grey
1981 911SC Wine Red
1997 911C4S Ocean Blue
Old 04-22-2009, 09:07 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #60 (permalink)
Reply


 


All times are GMT -8. The time now is 11:18 PM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.