How many 911 3.6 conversions out there ?

[Craig 930 RS]

You bet:

** My 930.......I present.....THE BEAST **

[skidmark]

3.6 conversion on a '82 SC wearing origional paint. I really prefer the sleeper look with no tail and factory finish wheels. Car weighs 2380lbs and is all steel except rear bumper and front spoiler. Will get a FVD hotwire conversion on a 92 964 motor and tuned on a dyno next week.
Mark Kinninger

[shahram]

Well, my project is not done yet but I thought i join the club since it is 3.6.

[911st]

Mahler,

What is up here. It looks like a single plug dist on a twin plug motor?

I always wondered why others have not used an earlier fan as I believe it moves more air.

Best argument I can think of for a air box it to keep from sucking hot air from under the car. Most do not go to much effort to ensure an effective seal.

Originally Posted by Mahler9th

Well, on my car the builder used a smaller 911 alternator and fan assembly. My car does not need a high alt output. This creates more space. Wiring is all custom-- I am not using a DME. See pic.

You can also see my first rough airbox propotype. Cold air enters through grill in fiberglass tailbase. I think it is "better air" than what is available closer to the throttle body. And for a car that is mostly for track use (occasional, loud street driving) my car has European headers and Phase 9-type mufflers.

[skinnerd]

73 RSR bodied w/ Rothsport 3.6 RS Vram

[Porsche84]

OK, I'll jump on board

This is an 84 with a 94 964

[scotiagreg]

Ruby was built by Instant G in 2002. She's an 82 SC with a 1996 Varioram.

[efhughes3]

Ruby?

[burgundyben]

I'd been holding off on adding to this thread until I had the car running.

Its a 78 SC, RHD, non sunroof coupe. Its generally very scruffy although I am improving that slowly, I call it 'The Shed'

I've fitted a 95 993 motor, patrick flywheel, sachs power clutch, single pulley. Not sure where the exhaust came from, motor was in an early car before I bought it and it came with the exhaust.





Scruffy ATS wheels have winter tyres on, in spring I'll be fitting a set of 15 inch Fuchs.

[Captain Ahab Jr]

Originally Posted by shahram

Well, my project is not done yet but I thought i join the club since it is 3.6.

Any more info. on the build spec. of this engine, it looks great!

[rothaus]

1971 911T with '90 964 SW Chip

from Engelbert's Site

Cheers
Engelbert

[oletobias911]

Craig. how did you get the rs carbon heater tube to fit? its to tight for me to fit the one i got:/

[Craig 930 RS]

CF tube was an easy fit - with all the extra stuff removed - IIRC (been 6 years since I sold the car)

[oletobias911]

i have removed allot. did you use the old engine mount or the original 993 mount?
do you got Any pictures or more info of how to get it in place?

[Joe Bob]

Versatile too.....

[amsterdamned]

3.8RS clubsport brand new...360HP,incl. a G50/31 gearbox.Must be ready next summer.More pix soon.

[antares]

Burgundyben: I like your setup with the engine removal. What are you attaching the rope ends to in the photo with the motor hoist?

What I guess you lift up the car to the height you need, then put the truck jacks under, remove the engine hoist, then slide the engine out? Pretty slick.

[tshebib]

I just finished my conversion last week. I'm now learning how to drive this thing all over again. The power is unbelievable!! Can't wait to get her on the track.

[ted]

more flogging for a 3.6.

[tshebib]

Originally Posted by ted

more flogging for a 3.6.

Thanks Ted. That was just what I needed