Pelican Parts
Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   Pelican Parts Forums > Porsche Forums > Porsche 911 Technical Forum


Reply
 
LinkBack Thread Tools Rate Thread
Author
Thread Post New Thread    Reply
Registered
 
flash951's Avatar
 
Join Date: Apr 2010
Posts: 232
How to remove fan

How to remove fan? I have removed the bolt in front and the belt. What more has to be loosened to remove the fan completely?

__________________
Remi Jakobsen
911T DP targa -71 (2.7L)
Phone: +47 92844671 (Norway)
Old 07-03-2012, 12:30 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #1 (permalink)
No sleep 'til... BROOKLYN
 
flatsixjunky's Avatar
 
Join Date: Jun 2008
Location: Brooklyn, N.Y.
Posts: 575
Garage
A funny thing about this cars is that even the most simple tasks can become a B. it's pretty hard to separate the fan from the alternator, be careful what you use to remove it, you don't want to damage it.

Actually I have never taken my fan out without the alternator, always together and then I separate those, using gravity while tapping gently in the spindle with a rubber mallet.

Take care
__________________
-Orlando-
'89 3.2L G-50
'77 S w '79, 3.0L
'90 T-3 Syncro
32C #16
Old 07-03-2012, 12:44 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #2 (permalink)
Registered
 
Brown747's Avatar
 
Join Date: Mar 2011
Location: Western WA
Posts: 695
Garage
Get a 6mm tap and tap out two of the holes in the fan 180 deg apart. Thread into the tapped holes 2 6mm bolts maybe 2 inches long. Tighten the bolts evenly, paying attention to where the bolt contacts the alternator and the fan will pop right off.
HTH Thor



__________________
1978 SC coupe #1834
Old 07-03-2012, 12:57 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #3 (permalink)
Registered
 
steely's Avatar
 
Join Date: Aug 2008
Location: sectors R&N, SE Pa
Posts: 3,117
Mine was easier although I had removed the entire alternator. You might try some penetrating oil. There is a woodruff key on the shaft, so be careful if you do remove the fan in the car, that the key doesn't drop somewhere.
There is a tech article here on removing the alternator, but the fan removal is just given lip service.

If you do decide to remove the entire fan/alt housing, be careful with the wires in the rear as their insulation is old and can easily be hurt.
I then used the John Walker method for separation by rapping the housing on rag covered wood / with the fan down. If I recall, the fan came off first with a little more work for the alternator.
__________________
Dan

'87 Targa Carrera 3.2 - Fabspeed Cat Bypass, M&K Muffler, SW Chip
Venetian Blue
Old 07-03-2012, 01:09 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #4 (permalink)
76 911S Targa
 
Join Date: Oct 2010
Location: Idaho
Posts: 1,150
I used a three jawed puller. First you must lift the fan housing up at an angle to allow space to fit the puller, then the fan pops loose with a couple of turns on the center bolt pushing against the pulley/alternator shaft. The three jaws fit on the central hub of the fan, between the fan blades. The alternator is left within the housing and can then either be removed or left until the fan is refitted.
__________________
76 911S, 2.7, Bursch Thermal Reactor Replacements, Smog Pump Removed, Magnecors, Silicone Valve Cover Gaskets, 11 Blade Fan, Carrera Oil Cooler, Turbo Tie Rods.
Old 07-03-2012, 02:46 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #5 (permalink)
Detached Member
 
Hugh R's Avatar
 
Join Date: May 2003
Location: southern California
Posts: 26,964
When I pulled my alt. the fan basically fell off the spindle.
__________________
Hugh
Old 07-03-2012, 02:48 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #6 (permalink)
 
83 911 Production Cab #10
 
JJ 911SC's Avatar
 
Join Date: Jun 2009
Location: Ottawa, Ontario, Canada
Posts: 11,134
Garage
Quote:
Originally Posted by Brown747 View Post
Get a 6mm tap and tap out two of the holes in the fan 180 deg apart. Thread into the tapped holes 2 6mm bolts maybe 2 inches long. Tighten the bolts evenly, paying attention to where the bolt contacts the alternator and the fan will pop right off.
HTH Thor

+1, work like a charm.

This is was my second tap ever. Not as stressing as my first one (Time-Sert for a broken exhaust stud).
__________________
Who Will Live... Will See

83 911 Production Cab #10, Slightly Modified: Unslanted, 3.2, PMO EFI, TECgt, CE 911 CAM Sync / Pulley / Wires, SSI, Dansk Sport 2/2, 17" Euromeister, CKO GT3 Seats, Going SOK Super Charger
Old 07-03-2012, 03:05 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #7 (permalink)
Registered
 
47silver's Avatar
 
Join Date: Sep 2002
Location: Pittsburgh
Posts: 3,039
Garage
Get a piece if 6 inch plastic pipe about a foot long. Put foam or towels inside pipe. Hold alt and fan above pipe, with alt facing down. Drop fan and alternator into pipe. Make sure fan blades do not hit edge of pipe viola! Alternator falls into pipe fan stays on top. Make sure the edge of fan hits the edge of pipe so you do not break the blades.
Old 07-03-2012, 03:23 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #8 (permalink)
Registered
 
47silver's Avatar
 
Join Date: Sep 2002
Location: Pittsburgh
Posts: 3,039
Garage
After reading your post. Make sure you disconnect the battery. After you loosen the clamp. Pull assembly out. You will have to remove the nuts that hold the plastic air deflector. Note how it is insattled before you remove it. Slide deflector away from the alternator, get a pen, mark how the wires are installed on the alternator posts. Remove alternator wires held on by 10mm and 8 mm nuts I believe. Remove alternator and fan. Do not pound on the ends of the bolts to remove the fan from the alternator. Let gravity work for you. Get 2 2x4's, place on top of a piece of foam or a bunch of towels. Hold fan shroud and fan above wood with fan blades facing down. Position wood so the edge if the wood hits edge of shroud. Drop assembly. The fan will come off. Use Method described above to remove fan blade from alt shaft.
Old 07-03-2012, 03:35 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #9 (permalink)
Senior Advisor
 
James Brown's Avatar
 
Join Date: Apr 2007
Location: Bellingham, WA
Posts: 5,479
Garage
Send a message via Yahoo to James Brown
John Walker's procedure works best, drop the edge of the fan (carefully) on a 4x4 block on the ground, rotate it and repeat till it drops out. no tools needed.
__________________
08 Cayenne Turbo
Old 07-03-2012, 03:48 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #10 (permalink)
Registered
 
Join Date: Dec 2010
Location: Auburn, WA
Posts: 54
Quote:
John Walker's procedure works best, drop the edge of the fan (carefully) on a 4x4 block on the ground, rotate it and repeat till it drops out. no tools needed.
+1, this is the procedure I used. Worked great!
Old 07-03-2012, 07:27 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #11 (permalink)
Registered
 
flash951's Avatar
 
Join Date: Apr 2010
Posts: 232
Thank you for tips, I don't want to remove the alt and everything, so I want to try the one with the 6 mm tap ...
__________________
Remi Jakobsen
911T DP targa -71 (2.7L)
Phone: +47 92844671 (Norway)
Old 07-04-2012, 01:09 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #12 (permalink)
 
83 911 Production Cab #10
 
JJ 911SC's Avatar
 
Join Date: Jun 2009
Location: Ottawa, Ontario, Canada
Posts: 11,134
Garage
Quote:
Originally Posted by flash951 View Post
Thank you for tips, I don't want to remove the alt and everything, so I want to try the one with the 6 mm tap ...
Way to go...
__________________
Who Will Live... Will See

83 911 Production Cab #10, Slightly Modified: Unslanted, 3.2, PMO EFI, TECgt, CE 911 CAM Sync / Pulley / Wires, SSI, Dansk Sport 2/2, 17" Euromeister, CKO GT3 Seats, Going SOK Super Charger
Old 07-04-2012, 02:03 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #13 (permalink)
Registered
 
tobluforu's Avatar
 
Join Date: Oct 2001
Posts: 4,018
Garage
Quote:
Originally Posted by msb911 View Post
+1, this is the procedure i used. Worked great!
+2

__________________
72 911
Although it is done at the moment, it will never be finished.
Old 07-04-2012, 02:41 PM
  Pelican Parts Catalog | Tech Articles | Promos & Specials    Reply With Quote #14 (permalink)
Reply


 


All times are GMT -8. The time now is 11:52 AM.


 
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page
 

DTO Garage Plus vBulletin Plugins by Drive Thru Online, Inc.